Timing Gears - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
B     | 9S-9154     | 踏脚板     | 1     |
1P-2322 | 拉拔器组件     | 1     |
开始:
- 拆下凸轮轴。
- 拆下螺栓 (1) 、止推板 (2) 和惰轮 (3) 。
Show/hide table
图 1 | g00788517 |
- 用工具 (A) 和适当的压具将轴承从惰轮 (3) 上拆下。
Show/hide table
图 2 | g00788525 |
- 将止推垫圈 (4) 、螺栓 (5 ) 和轴 (6) 从缸体上拆下。
Show/hide table
图 3 | g00788530 |
- 用工具 (B) 将齿轮 (7) 从曲轴上拆下。
Show/hide table
图 4 | g00788533 |
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
- 转动曲轴,使曲轴定位销 (8) 朝上。
Show/hide table
图 5 | g01424275 |
- 将曲轴齿轮 (7) 加热到 233° C (451° F) 的最高温度。 将曲轴齿轮 (7) 安装到曲轴上。 确保曲轴齿轮 (7) 有 "V" 正时标记的一侧朝外。 确保曲轴齿轮 (7) 中的槽(凹槽)与曲轴上的定位销 (8) 对齐。 确保曲轴齿轮 (7) 与油泵惰轮对齐。
- 安装轴 (6) 和螺栓 (5) 。 将清洁的发动机机油涂在垫圈 (4) 上。 将止推垫圈 (4) 安装在轴上,使油槽朝外。如图所示。
Show/hide table
图 6 | g00788530 |
- 用工具 (A) 和适当的压具将轴承安装到惰轮 (3) 中。
Show/hide table
图 7 | g00788525 |
- 安装轴承,使轴承接头(箭头)在惰轮 (3) 的固定区域。 将轴承安装至惰轮 (3) 表面以下 0.38 ± 0.25 mm (0.015 ± 0.010 in) 处。
Show/hide table
图 8 | g01424280 |
- 将清洁的发动机机油涂在轴承孔上。
- 将惰轮 (3) 安装到轴上。 确保 "V" 标记在惰轮 (3) 和曲轴齿轮 (7) 上对齐。
Show/hide table
图 9 | g01424281 |
- 将清洁的发动机机油涂在止推板 (2) 靠近惰轮 (3) 的一侧。 安装将板固定到位的止推板 (2) 和螺栓 (1) 。
Show/hide table
图 10 | g00788517 |
注: 安装止推板 (2) ,使止推板 (2) 有油槽的一侧朝向惰轮 (3) 。
End By: 安装凸轮轴
Caterpillar Information System:
CG137-08 and CG137-12 Engines Timing Gear Cover - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
C4.4 Marine Generator Set Before Starting Engine
C15 Engines for Combat and Tactical Vehicles Lubrication System
3516C Generator Sets Engine Crankcase Breather - Clean
3516C Generator Sets Glossary
C13, C15, and C18 Tier 4 Final Engines Front Housing and Covers
3516C Generator Set Engines Catalytic Converter Sensor
C13, C15, and C18 Tier 4 Final Engines Pressure Sensor (Exhaust Differential)
C9.3 Tier 4 Final Engines Flywheel Housing
CG137-08 and CG137-12 Generator Sets Flywheel
CG137-08 and CG137-12 Engines Valve Cover Base - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Rocker Shaft and Push Rod - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Cylinder Head - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Pistons and Connecting Rods - Remove and Install
CG137-08 and CG137-12 Engines Cylinder Liner - Remove and Install
CG137-08 and CG137-12 Engines Camshaft - Remove and Install
371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100} 371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100}
CG137-08 and CG137-12 Engines Camshaft Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Main Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft - Remove and Install
TH55FT-E70 and TH55FT-E90 Transmissions Daily Inspection
CG137-08 and CG137-12 Generator Sets Turbocharger