Camshaft - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-7307     | 发动机盘车工具     | 1     |
B     | 9M-1974     | 垫圈     | 2     |
1B-2713 | 螺栓     | 2     | |
C     | 1P-0510     | 冲头总成     | 1     |
开始:
- 拆下正时齿轮盖。 请参阅拆解和组装, "正时齿轮盖 - 拆卸和安装"。
- 拆下摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 拆下气门挺杆。 请参阅拆解和组装, "气门挺杆 - 拆卸"。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将管组件 (1) 从涡轮增压器底部断开。
Show/hide table
图 1 | g00790577 |
- 将管组件 (1) 和弯头 (2) 从飞轮壳上拆下。
- 拆下将弯头 (1) 固定在飞轮壳上的螺柱 (3) 。
Show/hide table
图 2 | g00790581 |
- 用工具 (A) 转动飞轮,使四个螺栓 (4) 中的三个可从后凸轮轴齿轮上拆下。 安装工具 (B) 。 拆下将后凸轮轴齿轮固定在凸轮轴上的最后一个螺栓。 拧紧工具 (B) ,将后凸轮轴齿轮从凸轮轴上断开。
Show/hide table
图 3 | g00790584 |
- 拆下将凸轮轴在缸体中固定到位的螺栓 (5) 和板 (6) 。
Show/hide table
图 4 | g00790603 |
- 从发动机上拆卸凸轮轴 (7) 。
Show/hide table
图 5 | g00790605 |
- 用工具 (C) 和适当的压具将前凸轮轴齿轮 (8) 从凸轮轴上拆下。
Show/hide table
图 6 | g00790606 |
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-7307     | 发动机盘车工具     | 1     |
B     | 9M-1974     | 垫圈     | 2     |
1B-2713 | 螺栓     | 2     | |
C     | 4C-5593     | 防粘结剂     | -     |
D     | 9S-3263     | 螺纹锁固胶     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将齿轮 (8) 加热到 315 °C (600 °F) 的最高温度。 将齿轮 (1) 安装到凸轮轴 (7) 上。
Show/hide table
图 7 | g01423949 |
注: 安装齿轮 (8) 前,确保齿轮 (8) 的键在凸轮轴 (7) 上就位。
- 将工具 (C) 涂在凸轮轴 (7) 的凸轮上。 将清洁的发动机机油涂在凸轮轴轴颈上。
Show/hide table
注意 |
---|
不要让工具 (C) 沾到凸轮轴上的轴承轴颈上。 |
- 转动曲轴,直到惰轮上的 (V) 标记朝向凸轮轴 (7) 的孔。
Show/hide table
图 8 | g00790605 |
- 将凸轮轴 (7) 安装到发动机中。
- 旋转发动机,直到凸轮轴齿轮 (8) 的 (V) 标记与惰轮 (9) 的标记对齐。
Show/hide table
图 9 | g01423952 |
- 安装将凸轮轴在发动机中固定到位的板 (6) 和螺栓 (5) 。
Show/hide table
图 10 | g00790603 |
- 用工具 (B) 将后凸轮轴齿轮中的螺栓孔与凸轮轴中的孔对齐。
Show/hide table
图 11 | g00790584 |
- 安装一个螺栓 (4) ,将凸轮轴齿轮固定到凸轮轴上。 拆下工具 (B) 。 拧紧螺栓 (4) 至扭矩为 27 ± 4 N·m (20 ± 3 lb ft)。
- 用工具 (A) 转动飞轮,使其他三个螺栓 (4) 可安装到后凸轮轴齿轮中。 拧紧螺栓 (4) 至 27 ± 4 N·m (20 ± 3 lb ft) 的扭矩。
- 将工具 (D) 涂在螺柱 (3) 上。 将螺柱 (3) 安装到飞轮壳中。
Show/hide table
图 12 | g00790581 |
- 确保密封垫在管组件 (1) 和涡轮增压器之间就位。 确保密封垫在弯头 (2) 和飞轮壳之间就位。 安装管组件 (1) 和弯头 (2) 。
Show/hide table
图 13 | g00790577 |
End By:
- 安装气门挺杆。 请参阅 拆解和组装, "气门挺杆 - 安装"。
- 安装摇臂轴组件和推杆。 请参阅 拆解和组装, "摇臂轴和推杆 - 安装"。
- 安装正时齿轮盖。 请参阅 拆解和组装, "正时齿轮盖 - 拆卸和安装"。
Caterpillar Information System:
CG137-08 and CG137-12 Engines Cylinder Liner - Remove and Install
CG137-08 and CG137-12 Engines Pistons and Connecting Rods - Remove and Install
CG137-08 and CG137-12 Engines Cylinder Head - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Rocker Shaft and Push Rod - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Valve Cover Base - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Timing Gears - Remove and Install
CG137-08 and CG137-12 Engines Timing Gear Cover - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
C4.4 Marine Generator Set Before Starting Engine
C15 Engines for Combat and Tactical Vehicles Lubrication System
3516C Generator Sets Engine Crankcase Breather - Clean
371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100} 371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100}
CG137-08 and CG137-12 Engines Camshaft Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Main Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft - Remove and Install
TH55FT-E70 and TH55FT-E90 Transmissions Daily Inspection
CG137-08 and CG137-12 Generator Sets Turbocharger
C15 Engines for Combat and Tactical Vehicles Electronic Unit Injector - Adjust
Installation Procedure for Improved Jacket Water Heater on Certain C27 Generator Sets{1383} Installation Procedure for Improved Jacket Water Heater on Certain C27 Generator Sets{1383}
3516C Generator Set Engines Magnetic Switch (DEF Tank Heater)
3516C Generator Set Engines Liquid Level Sensor (DEF)
2011/09/23 New Software Is Now Used to Improve the Programmable Torque Limiting Parameters on Certain C32 Marine Engines {1901, 1920}
G3516 Petroleum Engine Engine Oil Temperature Regulator - Replace