Clean Emissions Module - Remove and Install
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" M0066576
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite Heavy-Duty Anti-Seize (1) | 1 |
- | Loctite 8009 (2) | 1 |
Show/hide table
(1) | North America |
(2) | Outside North America |
Show/hide table
NOTICE |
---|
Ensure that all adjustments and repairs that are carried out to the Diesel Emission Fluid (DEF) system are performed by authorized personnel that have the correct training. Before beginning ANY work on the DEF system, refer to Operation and Maintenance Manual, "General Hazard" for safety information. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that Diesel Emission Fluid (DEF) for the system are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
Illustration 1 | g06286423 |
Show/hide table
Illustration 2 | g06290888 |
Show/hide table
Illustration 3 | g06290890 |
Show/hide table
Illustration 4 | g06290892 |
Show/hide table
Illustration 5 | g06290911 |
Show/hide table
Illustration 6 | g06290924 |
Show/hide table
Illustration 7 | g06291014 |
Show/hide table
Illustration 8 | g06291033 |
Show/hide table
Illustration 9 | g06291043 |
Show/hide table
Illustration 10 | g06291072 |
Show/hide table
Illustration 11 | g06291094 |
Show/hide table
Illustration 12 | g06291097 |
Remove all cable straps. |
Show/hide table
Illustration 13 | g06291502 |
Show/hide table
Illustration 14 | g06291306 |
Show/hide table
Illustration 15 | g06291504 |
- Install the clean emissions module in the reverse order of removal.
Show/hide table
Illustration 16 | g06291554 |
Hand tighten the top nuts. If there is a gap between the pipe and the bracket, tighten the nut until the gap is eliminated. |
Show/hide table
Illustration 17 | g06291568 |
Show/hide table
Illustration 18 | g06291576 |
Do not exceed 75 RPM max wrench speed. |
Caterpillar Information System:
3608 Engine Maintenance Interval Schedule
307, 308, 309 and 310 EXCAVATOR Air Cleaner
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System General Information (Swing System)
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Turbocharger - Remove and Install
336, 336 GC and 340 Excavator Systems Pilot Lines
336 Excavator Machine Systems Travel Motor - Assemble
336 Excavator Machine Systems Travel Motor - Disassemble
336, 336 GC and 340 Excavator Systems Hydraulic Tank and Filter
336, 336 GC and 340 Excavator Systems Position Sensor and Mounting
336, 336 GC and 340 Excavator Systems Hydraulic Pedal Control (Travel)
336, 336 GC and 340 Excavator Systems Pump Coupling
336, 336 GC and 340 Excavator Systems Hydraulic Oil Lines
336, 336 GC and 340 Excavator Systems Hydraulic System Air - Purge - Fan Pump
336, 336 GC and 340 Excavator Systems Hydraulic System Air - Purge - Auxiliary Pump and PTO Drive
307, 308, 309 and 310 EXCAVATOR Air Conditioner Lines
307, 308, 309 and 310 EXCAVATOR Air Cleaner
307, 308, 309 and 310 EXCAVATOR Blade Lift Cylinder
PM820, PM822, and PM825 Cold Planer Machine Systems Control Valve - Remove and Install - Rear
C27 and C32 Generator Set Engines Fan Drive - Remove and Install - Upper Fan Drive
C27 and C32 Generator Set Engines Fan Drive - Remove and Install - Lower Fan Drive
TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565} TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565}
C7.1 Marine Propulsion Engine Belts - Inspect/Adjust/Replace
C7.1 Marine Propulsion Engine System Pressure Release
336, 336 GC and 340 Excavator Systems Accumulator (Pilot) - Test and Charge - Pump Actuator