New Software Is Used on Certain C7 and C9 Engines {1920} Caterpillar


New Software Is Used on Certain C7 and C9 Engines {1920}

Usage:

C7 C7D
Marine Engine
C7 MARINE (S/N: M7A1-UP; C7D1-UP; C7Z1-UP)
C9 MARINE (S/N: X9X1-UP; Z9X1-UP; X9Y1-UP)

Description Of Change: The new software has improved to allow programming of the current engine hours and to retain the timing cal and equipment ID during the software flash.

Adaptable To: The new software replaces the former software. The new software is adaptable back to the first production on the serial numbers listed above.

The new software and former software are listed in Table 1.

Table 1
New Part Number  Description  Former Part Number 
488-8802  SFWR GP-A1000  299-9143 
491-6277  SFWR GP-A1000  291-1549 
491-6280  SFWR GP-A1000  338-2383 
This change is effective for the serial numbers listed in Table 2.

Table 2
Effective Serial Numbers 
S/N:C7D03029-UP 
S/N:C7Z00430-UP 
S/N:M7A01049-UP 
S/N:X9X03065-UP 
S/N:X9Y05105-UP 
S/N:Z9X00888-UP 

Caterpillar Information System:

C18 Generator Set Engines Diesel Exhaust Fluid Module - Disassemble
G3512 Generator Set Engines Throttle Actuator - Test
A New Sea Water Pump Is Used on Certain 3608 Marine Auxiliary Engines {1371} A New Sea Water Pump Is Used on Certain 3608 Marine Auxiliary Engines {1371}
XQ570 Rental Generator Set Electronic Modular Control Panel 4 (EMCP 4)
XQ570 Rental Generator Set Voltage Regulators
C175-20 Locomotive Engine Nitrogen Oxide Sensor - Replace
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Sensor Signal (Analog, Active) - Test
C175-20 Locomotive Engine Overhaul (Major)
Exhaust Gas Valve (NRS) for C7.1, C6.6, andC4.4 Engines {1050, 108N} Exhaust Gas Valve (NRS) for C7.1, C6.6, andC4.4 Engines {1050, 108N}
C18 Generator Set Engines Relay (ARD Nozzle Heater) - Remove and Install
C175-20 Locomotive Engine Overhaul (Intermediate)
C175-20 Locomotive Engine Overhaul Considerations
Discharge Flange Instructions for Well Stimulation Pumps {5234, 6002} Discharge Flange Instructions for Well Stimulation Pumps {5234, 6002}
C175-20 Locomotive Engine Starting the Engine
C175-16 Locomotive Engine Diesel Exhaust Fluid Nozzle - Inspect/Clean
Technical Analysis 1 (TA1) Visual Inspection for Marine Engine {0372, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for Marine Engine {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Off-Highway Trucks {0372, 0374, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for Off-Highway Trucks {0372, 0374, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Paving Compactors {0372, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for Paving Compactors {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Petroleum Gas Compression Engine {0372, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for Petroleum Gas Compression Engine {0372, 1000, 7000, 753S, 7565}
New Fuel Injection Pump Stop Solenoid is Available on Certain 3054C and C7.1 (Mech) Engines {1251} New Fuel Injection Pump Stop Solenoid is Available on Certain 3054C and C7.1 (Mech) Engines {1251}
G3512 Generator Set Engines Turbocharger Compressor Bypass - Test
PM820, PM822, and PM825 Cold Planer Before Starting Engine
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System ECM Location Code - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Sensor Signal (Analog, Passive) - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.