G3500 Engines Caterpillar


Cold Weather Starting

Usage:

G3516B JEF
Note: Oil pan immersion heaters are not recommended for heating the lube oil. To ensure the compatibility of the components, only use equipment that is recommended by Caterpillar.

A jacket water heater is required for starting when the temperature is less than 16 °C (60 °F). The jacket water heater can maintain the water temperature at approximately 32 °C (90 °F). The heated water will help to keep the oil in the engine block warm enough to flow when the engine is started.

For air starting motors, a larger volume of starting air and/or a higher air pressure may be necessary to start the engine at colder temperatures.

For electric starting, extra battery capacity may be necessary.

Consult your Cat dealer for more information on the starting aids that are available for cold weather starting.

Caterpillar Information System:

G3500 Engines Configuration Parameters
A New Crankshaft Is Available For Certain C4.4 Engines {1202} A New Crankshaft Is Available For Certain C4.4 Engines {1202}
Technical Analysis 1 (TA1) Visual Inspection for Cold Planer {0372, 1000, 7000, 753T, 7565} Technical Analysis 1 (TA1) Visual Inspection for Cold Planer {0372, 1000, 7000, 753T, 7565}
A New Diesel Exhaust Fluid Filter is Now Available for C7.1 Engines {108H} A New Diesel Exhaust Fluid Filter is Now Available for C7.1 Engines {108H}
HPU300 Hydraulic Power Pack Hydraulic System Oil Level - Check
Certain C9 Industrial Engines Can Over Speed After Start Up {1920} Certain C9 Industrial Engines Can Over Speed After Start Up {1920}
Inspection Procedure for Boom Cylinder Assembly Cracks on Certain 330B, 330C, 345B, 345C, and 345D Excavators {5456, 7562} Inspection Procedure for Boom Cylinder Assembly Cracks on Certain 330B, 330C, 345B, 345C, and 345D Excavators {5456, 7562}
HPU300 Hydraulic Power Pack Indicators and Gauges - Check
G3500 Generator Sets Maintenance Interval Schedule - Natural Gas
G3500 Generator Sets Maintenance Interval Schedule - Turbocharged Aftercooled
G3500 Generator Sets Maintenance Interval Schedule - Bio Gas
C12.9 Marine Propulsion Engine Air Inlet and Exhaust System
G3500 Engines Starting the Engine
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1674 - FMI 03
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1674 - FMI 04
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1674 - FMI 05
G3500 Engines Manual Stop Procedure
G3500 Engines Refill Capacities
G3500 Engines Fluid Recommendations
Crankshaft Pre-Assembly Instructions for Well Stimulation Pumps {1202} Crankshaft Pre-Assembly Instructions for Well Stimulation Pumps {1202}
A New Instruction to Change the Configuration Settings Of Generator Reverse Reactive Power is Now Available On Certain Generator Sets {4490} A New Instruction to Change the Configuration Settings Of Generator Reverse Reactive Power is Now Available On Certain Generator Sets {4490}
G3500 Engines Belts - Inspect/Adjust/Replace
G3500 Engines Compressor Bypass - Check
C7.1 Commercial Marine Engine Water Temperature Regulator - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.