Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-7262 | 伸缩式磁铁 | 1 |
开始:
- 拆下发动机油底壳。 请参阅解体和组装, "发动机油底壳 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 松开盖 (2)。 小心地从平衡器 (1) 上卸下盖。
注: 拆下盖后会释放弹力。
- 从平衡器 (1) 中的安全阀孔上卸下弹簧 (3)。
- 使用工具 (A),从平衡器 (1) 中的安全阀孔上卸下柱塞 (4)。
Show/hide table
图 1 | g01470291 |
典型示例 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-7262 | 伸缩式磁铁 | 1 |
B | 4C-4030 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。 如果平衡器 (1) 中的安全阀孔磨损或损坏,必须更换整个平衡器组件。
- 使用清洁的发动机机油润滑柱塞 (4)。 将柱塞 (4) 和弹簧 (3) 安装到平衡器 (1) 的安全阀孔中。
注: 柱塞必须能在安全阀孔中自由滑动。
- 将工具 (B) 涂敷在盖 (2) 的螺纹上。 将盖 (2) 安装到平衡器 (1) 上。 拧紧盖至扭矩为
21 N·m (15.5 lb ft) 。注: 确保弹簧正确位于柱塞和盖内。 确保工具 (B) 没有污染平衡器 (1) 中的安全阀孔。
Show/hide table
图 2 | g01470291 |
典型示例 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
结束:
- 安装发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C3.4B Engines for Caterpillar Built Machines Rocker Shaft
C4.4 Engines for Caterpillar Built Machines Balancer - Install
C4.4 Engines for Caterpillar Built Machines Balancer - Remove
793F and 797F Off-Highway Trucks Braking System E653 Low Secondary Brake Accumulator Pressure
C3.4B Engines for Caterpillar Built Machines Cylinder Head
C4.4 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Turbocharger - Install - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Refrigerant Compressor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C3.4B Engines for Caterpillar Built Machines Camshaft Bearings
C8.7 Marine Engine Engine Oil Level Gauge - Calibrate
C3.4B Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
C4.4 Engines for Caterpillar Built Machines Electronic Control Module - Remove and Install
C3.4B Engines for Caterpillar Built Machines Main Bearing Journal
C3.4B Engines for Caterpillar Built Machines Connecting Rod
C3.4B Engines for Caterpillar Built Machines Piston and Rings
TA2 Technical Inspection for 3512C Dynamic Gas Blending Marine Engines{0372, 1000, 753T, 7565} TA2 Technical Inspection for 3512C Dynamic Gas Blending Marine Engines{0372, 1000, 753T, 7565}
C3.4B Engines for Caterpillar Built Machines Lifter Group
C3.4B Engines for Caterpillar Built Machines Cylinder Head Valves