Lifter Group - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 9U-6198 | 曲轴转动工具 | 1 |
B | 1U-7262 | 伸缩磁铁 | 1 |
开始:
- 如果发动机配备平衡器,则卸下该平衡器。 请参阅拆解和组装, "平衡器 - 拆卸"。 如果发动机未配备平衡器,则卸下发动机机油泵。 请参阅拆解和组装, "发动机油泵 - 拆卸和安装"。
- 拆下凸轮轴。 请参阅拆解和组装, "凸轮轴 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 如果安装了曲轴,使用工具 (A) 转动曲轴,以便进入挺杆。
Show/hide table
图 1 g01476632 典型示例 - 使用工具 (B) 拆卸挺杆 (1)。
注: 在各挺杆上作临时识别标记,以确定正确位置。
- 重复步骤 1 至步骤 2 卸下其余的挺杆。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 9U-6198 | 曲轴转动工具 | 1 |
B | 1U-7262 | 伸缩磁铁 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
强烈推荐应在安装新凸轮轴时更换所有的挺杆。 |
- 清洁挺杆。 遵循步骤 1.a 至步骤1.c 检查挺杆。 更换已磨损或损坏的挺杆。
- 检查挺杆中的推杆座有无可见的磨损或损坏。
- 检查挺杆柄有无磨损或损坏。 更多信息请参阅技术参数, "挺杆总成"。
- 检查挺杆接触凸轮轴的表面有无可见的磨损或损坏。
- 如果安装了曲轴,使用工具 (A),转动曲轴。 转动曲轴,以便靠近缸体来安装挺杆 (1)。
- 使用清洁的发动机机油润滑挺杆 (1)。
Show/hide table
图 2 g01476632 典型示例 - 使用工具 (B) 将挺杆 (1) 安装到缸体上。 确保旧挺杆安装位置正确。
注: 挺杆应能自由转动。
- 重复步骤 1 到步骤 4,安装其余的挺杆。
结束:
- 安装凸轮轴。 请参阅拆解和组装, "凸轮轴 - 拆卸和安装"。
- 如果发动机配备平衡器,则安装该平衡器。 请参阅拆解和组装, "平衡器 - 安装"。 如果发动机未配备平衡器,则安装发动机机油泵。 请参阅拆解和组装, "发动机油泵 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C175-16 PETROLEUM ENGINES Fuel Transfer Pump - Remove and Install
XQC1200 and XQC1600 Power Modules Exhaust Manifold - Remove and Install
C280 Marine Engines Crankcase Pressure Is High
C175-16 PETROLEUM ENGINES Fuel Priming Pump - Remove and Install
XQC1200 and XQC1600 Power Modules Air Inlet Manifold - Remove and Install
455-1192 Top End Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1192 Top End Overhaul Foundational Kit for C18 Marine Engines{1000}
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Turbocharger - Install - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
C3.4B Engines for Caterpillar Built Machines Cylinder Head
793F and 797F Off-Highway Trucks Braking System E653 Low Secondary Brake Accumulator Pressure
C4.4 Engines for Caterpillar Built Machines Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Balancer - Install
C3.4B Engines for Caterpillar Built Machines Rocker Shaft
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Refrigerant Compressor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold