Exhaust Elbow - Remove and Install
Show/hide table
图 1 | g01798993 |
典型示例 |
- 将螺栓 (7) 和排气弯头 (4) 从涡轮增压器 (1) 上拆下。 记录排气弯头的方位。
- 拆下螺母 (5),然后拆下适配器 (2)。
- 如有必要,拆下螺栓 (6),从缸体上拆下支架 (3)。
Show/hide table
图 2 | g01798993 |
典型示例 |
- 确保排气弯头、适配器和涡轮增压器出口没有损坏。 更换任何损坏的部件。
- 安装适配器 (2) 至涡轮增压器 (1)。
- 安装螺母 (5)。 逐步拧紧螺母。 拧紧螺母 (5) 至扭矩为
25 N·m (18 lb ft) 。 - 如有必要,将支架 (3) 安装到缸体上,然后安装螺栓 (6)。 将螺栓拧紧至
44 N·m (33 lb ft) 的扭矩。 - 安装螺栓 (7) 并用手拧紧。
- 确保涡轮增压器和排气弯头之间的间隙等距。
- 拧紧螺栓 (7) 至扭矩为
44 N·m (33 lb ft) 。
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Turbocharger - Install - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C175-16 PETROLEUM ENGINES Fuel Transfer Pump - Remove and Install
XQC1200 and XQC1600 Power Modules Exhaust Manifold - Remove and Install
C280 Marine Engines Crankcase Pressure Is High
C3.4B Engines for Caterpillar Built Machines Cylinder Head
793F and 797F Off-Highway Trucks Braking System E653 Low Secondary Brake Accumulator Pressure
C4.4 Engines for Caterpillar Built Machines Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Balancer - Install
C3.4B Engines for Caterpillar Built Machines Rocker Shaft
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Refrigerant Compressor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C3.4B Engines for Caterpillar Built Machines Camshaft Bearings
C8.7 Marine Engine Engine Oil Level Gauge - Calibrate
C3.4B Engines for Caterpillar Built Machines Connecting Rod Bearing Journal