Flywheel Housing - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 8B-7548 | Push-Puller Tool Group | 1 |
8B-7559 | Adapter | 2 | |
8H-0684 | Ratchet Wrench | 1 | |
8B-7561 | Step Plate | 3 | |
B | 138-7573 | Link Bracket | 2 |
C | 169-5464 | Quick Cure Primer | - |
Start By:
- Remove the starting motors. Refer to Disassembly and Assembly, "Air Starting Motor - Remove" or Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
- If the exhaust elbow is attached to the flywheel housing, remove the exhaust elbow and remove the bracket for the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install".
- Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use the timing pins in order to properly time the engine. Refer to Testing and Adjusting, "Camshaft Timing". Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston".
- Remove the crankshaft rear seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Rear Seal and Wear Sleeve - Remove".
- Remove the camshaft covers and gaskets.
- Remove the bolts and plates from the camshafts.
Show/hide table
Illustration 1 g00912881 - Use Tooling (A) in order to remove camshaft drive gears (1).
Show/hide table
Illustration 2 g00912883 - Install Tooling (B) into flywheel housing (2). Attach a suitable lifting device to Tooling (B). The weight of flywheel housing (2) is approximately
251 kg (553 lb) . - Remove the bolts and remove flywheel housing (2) and the gasket.
- After removing flywheel housing (2), clean the mating surface of the cylinder block and the mating surface of the flywheel housing with Tooling (C). If necessary, use a gasket scraper and a solvent in order to remove any residual gasket material. Both mating surfaces must be clean, dry, and free of any oil before installation.
Caterpillar Information System:
Reusability Guidelines for Single Tooth Master Links {0729, 4150, 4169, 4171} Reusability Guidelines for Single Tooth Master Links {0729, 4150, 4169, 4171}
3516B Engine Flywheel - Remove and Install
3516B Engine Crankshaft Front Seal and Wear Sleeve - Install
PM3516 Power Modules Starting Motor - Inspect
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Hoses and Clamps - Inspect/Replace
G3500H 50Hz Generator Sets Generator - Dry
2012/08/07 New Thermostats Are Now Used for Jacket Water Heater on Certain Cat Gensets and Cat Engines {1383}
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Fuel Filter Differential Pressure - Check - Gas Fuel System
G3500H 50Hz Generator Sets Flexible Coupling - Inspect
C27 Generator Set Air Shutoff - Test
C18 Marine Auxiliary and Marine Generator Set Engines Engine Oil Pressure - Test
320D2 and 323D2 Excavators Machine Systems Specifications Boom Cylinder Lines
C18 Marine Engines Engine Stalls at Low RPM
3516B Engine Engine Oil Sequence Valves - Remove and Install
3516B Engine Gear Group (Rear) - Remove
G3500H 60Hz Generator Sets Spark Plugs - Inspect/Adjust/Replace
C32 Auxiliary Engine Control Panel - Cat Marine Engine Control Panel I (MECP I) (If Equipped)
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Turbocharger
2012/12/10 A Revised Application and Installation Guide Is Now Available for Certain Industrial Engines {1000}
C175-16 and C175-20 Generator Set Engines Turbocharger