Gear Group (Rear) - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Group | 1 |
Start By:
- Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- The engine must be put in time before the flywheel housing is removed. This is done in order to make sure that the rear gear group is in alignment with the rotation of the engine, as shown.
Show/hide table
Illustration 2 g00913045 - Remove plate (1) and gear (2).
Show/hide table
Illustration 3 g00913049 - Use Tooling (A) and a suitable press to remove bearing (3) from gear (2).
Show/hide table
Illustration 4 g00913054 - Remove the bolts, the washers, and camshaft idler gears (4).
Show/hide table
Illustration 5 g01051669 - Remove washers (6) and shafts (5) from camshaft idler gears (4).
- Use Tooling (A) and a suitable press to remove bearings from camshaft idler gears (4).
Show/hide table
Illustration 6 g00913136 - Remove the bolts from shaft (7) and remove shaft (7).
Show/hide table
Illustration 7 g00913137 - Remove the bolts and crankshaft gear (8) from the end of the crankshaft.
Note: The following Step is for a 3508 Engine.
Show/hide table
Illustration 1 | g01056631 |
Caterpillar Information System:
3516B Engine Engine Oil Sequence Valves - Remove and Install
C18 Marine Engines Engine Stalls at Low RPM
3516B Engine Flywheel Housing - Remove
Reusability Guidelines for Single Tooth Master Links {0729, 4150, 4169, 4171} Reusability Guidelines for Single Tooth Master Links {0729, 4150, 4169, 4171}
3516B Engine Flywheel - Remove and Install
3516B Engine Crankshaft Front Seal and Wear Sleeve - Install
PM3516 Power Modules Starting Motor - Inspect
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Hoses and Clamps - Inspect/Replace
G3500H 50Hz Generator Sets Generator - Dry
2012/08/07 New Thermostats Are Now Used for Jacket Water Heater on Certain Cat Gensets and Cat Engines {1383}
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Fuel Filter Differential Pressure - Check - Gas Fuel System
G3500H 50Hz Generator Sets Flexible Coupling - Inspect
G3500H 60Hz Generator Sets Spark Plugs - Inspect/Adjust/Replace
C32 Auxiliary Engine Control Panel - Cat Marine Engine Control Panel I (MECP I) (If Equipped)
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Turbocharger
2012/12/10 A Revised Application and Installation Guide Is Now Available for Certain Industrial Engines {1000}
C175-16 and C175-20 Generator Set Engines Turbocharger
3516B Engine Gear Group (Rear) - Install
3516B Engine Piston Cooling Jets - Remove and Install
3516B Engine Bearing Clearance - Check