Transmission Planetary - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7574     | 连杆支架     | 3     |
B     | 1U-9200     | 操纵杆滚轮举倾机构     | 1     |
C     | 138-7575     | 连杆支架     | 2     |
D     | -     | 顶出螺栓 1/2 - 13 × 3 in     |
2     |
E     | 1P-2420     | 变速箱修复台     | 1     |
F     | -     | Loctite #540     | -     |
开始:
- 卸下变速箱液压控制阀。
- 分离变速箱和变矩器。
- 拆下转速传感器。
- 将工具 (A) 、工具 (B) 和适当的起吊设备固定到变速箱壳体 (1) 上。 变速箱壳体 (1) 的重量约为 ()。
Show/hide table
图 1 | g02911720 |
- 将变速箱壳体 (1) 放置到适当的垫块上。
Show/hide table
图 2 | g02911777 |
- 将工具 (C) 和适当的起吊设备固定到变速箱行星齿轮 (3) 上。 变速箱行星齿轮 (3) 的重量约为 871 kg (1920 lb)。
Show/hide table
图 3 | g02911780 |
- 拆下螺栓 (3 ) 。 使用工具 (D) 以拆下变速箱行星齿轮 (2) 。
Show/hide table
图 4 | g02911837 |
- 将工具 A 固定到变速箱行星齿轮 (2) 上。 将变速箱行星齿轮 (2) 固定到工具 (E) 上,如图所示。
Show/hide table
图 5 | g02911899 |
安装步骤
- 按与拆卸相反的顺序安装变速箱行星齿轮 (2) 。
- 将工具 (F) 涂抹到螺栓 (3) 的垫圈两侧。
Caterpillar Information System:
Installation Procedure for 281-8236 Auxiliary Hydraulic Lines Gp Stick on Certain Hydraulic Excavators {5057} Installation Procedure for 281-8236 Auxiliary Hydraulic Lines Gp Stick on Certain Hydraulic Excavators {5057}
PMG3516 Power Module Coolant Level - Check
C9.3 Tier 4 Final Engines Gear Group (Front) - Time
C32 Auxiliary Engine Product Description
PMG3516 Power Module Belts - Inspect/Adjust/Replace
PMG3516 Power Module Emergency Stopping
PMG3516 Power Module Sensors and Electrical Components
C175-16 Marine Propulsion Engines Starting - Test
PMG3516 Power Module Alarms and Shutoffs
C3.8 Engines for Caterpillar Built Machines Water Temperature Regulator
PMG3516 Power Module Plate Locations and Film Locations
CX48-P2300 Petroleum Transmission Transfer Gear Planetary (Speed Increase) - Remove and Install
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Component Location
Failure Of Water In Fuel Separator (WIF) Sensor On Certain CAT Products{1263, 1439} Failure Of Water In Fuel Separator (WIF) Sensor On Certain CAT Products{1263, 1439}
2012/03/26 A New Engine Oil Supply Line Is Used on Certain C32 Petroleum Engines {1165, 1207}
2012/03/05 A New Torque is Used for the Alternator Mounting Groups on Certain C18 Marine Engines {1154, 1405, 1405}
2012/03/05 A New Torque is Used for the Alternator Mounting Groups on Certain C32 Marine Engines {1154, 1405}
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Refrigerant Compressor
CX48-P2300 Petroleum Transmission Transmission Planetary - Disassemble
PMG3516 Power Module Engine Oil Filter - Change
C175-16 Marine Propulsion Engines Switch Circuits - Test
PMG3516 Power Module Engine Oil Level - Check
PMG3516 Power Module Spark Plugs - Inspect/Replace
2012/11/09 Using the Correct Part Numbers for Making Fuel Hoses from Bulk Hose Stock on Certain C32 Commercial Engines {1274}