Water Pump - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud M8 by 90 mm |
2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. |
- Ensure that the water pump is clean and free from wear and damage. If necessary, replace the water pump. Clean the gasket surface of the water pump.
Show/hide table
Illustration 1 g02164797 Show/hide tableIllustration 2 g02164963 - Clean the gasket surface of housing (1).
- Install Tooling (A) in Position (X).
- Use Tooling (A) in order to align new gasket (2) to housing (1). Install the gasket onto the housing.
- Align water pump (3) to Tooling (A). Install the water pump to housing (1).
Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
- Install bolts (4). Refer to Illustration 1. Tighten the bolts finger tight.
- Remove Tooling (A) and install remaining bolts (4).
Show/hide table
Illustration 3 g01985813 - Tighten the bolts in the sequence that is shown in Illustration 3 to a torque of
22 N·m (195 lb in) . - Install the hose to the water pump inlet. Tighten the hose clamps securely.
- Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
End By:
- Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Caterpillar Information System:
C7.1 Industrial Engine Wastegate Solenoid - Remove and Install
C7.1 Industrial Engine Vibration Damper and Pulley - Remove
C7.1 Industrial Engine Vibration Damper and Pulley - Install
C7.1 Industrial Engine Valve Mechanism Cover - Remove and Install
C7.1 Industrial Engine Turbocharger - Remove - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Remove - First Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - First Stage Turbocharger
C7.1 Industrial Engine Throttle Valve (Intake Air) - Remove
C7.1 Industrial Engine Throttle Valve (Intake Air) - Install
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine Temperature Sensor (DPF) - Remove and Install - Temperature Sensor (DPF) and Flame Detection Sensor
C7.1 Industrial Engine Water Pump - Remove
C7.1 Industrial Engine Water Temperature Regulator - Remove and Install
C7.1 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000} Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000}
C4.4 Industrial Engine Crankshaft Pulley
C15 Generator Sets Generator Start-up Checklist
3500 Petroleum Engines and Petroleum Generator Sets Safety Messages
349F and 352F Excavators Machine System Pilot Valve (Swing Parking Brake)
C4.4 Industrial Engine Crankshaft
C7.1 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C7.1 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C7.1 Industrial Engine Air Compressor - Remove and Install - Single Cylinder