Vibration Damper and Pulley - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Guide Stud M14 x 1.5 by 100 mm     |
1     |
B     | 227-4393     | E18 Torx Socket     | 1     |
Start By:
- Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the crankshaft adapter is approximately 22 kg (48 lb).
- Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to remove one Torx screws (1) from crankshaft pulley assembly (2) .
Show/hide table
Illustration 1 | g02368017 |
- Install Tooling (A) into crankshaft pulley assembly (2) .
- Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
- Remove crankshaft pulley assembly (2) .
- Tooling (A) .
- If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the crankshaft.
- Remove the front seal from the front cover. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install" for the correct procedure.
- Remove friction shim (3) .
Show/hide table
Illustration 2 | g02368018 |
- If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper, crankshaft pulley from crankshaft adapter.
- Place the crankshaft pulley assembly onto a suitable support.
- Remove bolts (7) from crankshaft pulley assembly (2) .
- Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
Caterpillar Information System:
C7.1 Industrial Engine Vibration Damper and Pulley - Install
C7.1 Industrial Engine Valve Mechanism Cover - Remove and Install
C7.1 Industrial Engine Turbocharger - Remove - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Remove - First Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - First Stage Turbocharger
C7.1 Industrial Engine Throttle Valve (Intake Air) - Remove
C7.1 Industrial Engine Throttle Valve (Intake Air) - Install
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine Temperature Sensor (DPF) - Remove and Install - Temperature Sensor (DPF) and Flame Detection Sensor
C7.1 Industrial Engine Soot Antenna - Remove and Install
C7.1 Industrial Engine Rocker Shaft and Pushrod - Remove
C7.1 Industrial Engine Wastegate Solenoid - Remove and Install
C7.1 Industrial Engine Water Pump - Install
C7.1 Industrial Engine Water Pump - Remove
C7.1 Industrial Engine Water Temperature Regulator - Remove and Install
C7.1 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000} Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000}
C4.4 Industrial Engine Crankshaft Pulley
C15 Generator Sets Generator Start-up Checklist
3500 Petroleum Engines and Petroleum Generator Sets Safety Messages
349F and 352F Excavators Machine System Pilot Valve (Swing Parking Brake)
C4.4 Industrial Engine Crankshaft
C7.1 Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "B"