Vibration Damper and Pulley - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Guide Stud M14 x1.5 by 100 mm     |
1     |
B     | 227-4393     | E18 Torx Socket     | 1     |
C     | 8T-3052     | Degree Wheel     | 1     |
D     | -     | Guide Stud M12 x1.75 by 50 mm     |
2     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from damage.
Show/hide table
Illustration 1 | g02368018 |
- Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
- If necessary, follow Step 3.a through Step 3.e in order to install vibration damper, crankshaft pulley to crankshaft adapter.
- Place crankshaft adapter (4) onto a suitable support.
- Install Tooling (D) crankshaft adapter (4) .
- Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
- Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
- Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
- If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install friction shim (3) .
- Install friction shim (3) .
- Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove and Install" for the correct procedure.
- Install Tooling (A) to the crankshaft.
- Install crankshaft pulley assembly (2) onto the crankshaft.
Show/hide table
Illustration 2 | g02368017 |
- Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
- Remove Tooling (A) .
- Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
- Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1) to a torque of 40 N·m (29 lb ft).
- Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove and Install" for the correct procedure.
Caterpillar Information System:
C7.1 Industrial Engine Valve Mechanism Cover - Remove and Install
C7.1 Industrial Engine Turbocharger - Remove - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - Second Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Remove - First Stage Turbocharger
C7.1 Industrial Engine Turbocharger - Install - First Stage Turbocharger
C7.1 Industrial Engine Throttle Valve (Intake Air) - Remove
C7.1 Industrial Engine Throttle Valve (Intake Air) - Install
C7.1 Industrial Engine Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C7.1 Industrial Engine Temperature Sensor (DPF) - Remove and Install - Temperature Sensor (DPF) and Flame Detection Sensor
C7.1 Industrial Engine Soot Antenna - Remove and Install
C7.1 Industrial Engine Rocker Shaft and Pushrod - Remove
C7.1 Industrial Engine Rocker Shaft and Pushrod - Install
C7.1 Industrial Engine Vibration Damper and Pulley - Remove
C7.1 Industrial Engine Wastegate Solenoid - Remove and Install
C7.1 Industrial Engine Water Pump - Install
C7.1 Industrial Engine Water Pump - Remove
C7.1 Industrial Engine Water Temperature Regulator - Remove and Install
C7.1 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000} Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000}
C4.4 Industrial Engine Crankshaft Pulley
C15 Generator Sets Generator Start-up Checklist
3500 Petroleum Engines and Petroleum Generator Sets Safety Messages
349F and 352F Excavators Machine System Pilot Valve (Swing Parking Brake)
C4.4 Industrial Engine Crankshaft