Vibration Damper - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 323-4712     | 导向螺栓 M24 × 500 mm     |
2     |
- 拆下两个螺栓 (1) 。
Show/hide table
图 1 | g02318815 |
- 安装工具 (A) 。 拆下剩余的螺栓 (1) 。
Show/hide table
图 2 | g02319053 |
- 拆下隔套 (2) 。 将减振器 (3) 在工具 (A) 上滑动。
Show/hide table
图 3 | g01204850 |
- 将适当的起吊设备连接到减振器 (3) 上。 减振器 (3) 的重量约为 195 kg (430 lb)。 将减振器 (3) 滑到工具 (A) 的端部。 拆下减振器 (3) 。
Show/hide table
图 4 | g01204854 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 323-4712     | 导向螺栓 M24 × 500 mm     |
2     |
B     | 334-0519     | 润滑脂     |     |
- 将适当的起吊设备连接到减振器 (3) 上。 减振器 (3) 的重量约为 195 kg (430 lb)。 安装工具 (A) 。 将减振器 (3) 安置在工具 (A) 上。 将减振器 (3) 在工具 (A) 上滑动。 拆下适当的起吊设备。
Show/hide table
图 5 | g01204854 |
- 安置减振器 (3) 。 将隔套 (2) 定位到工具 (A) 上。
Show/hide table
图 6 | g01204850 |
- 在螺栓头下方和螺纹上涂覆工具 (B) 。 将四个螺栓 (1) 安装在埋头孔内并用手拧紧。 拆下工具 (A) 。
Show/hide table
图 7 | g02319053 |
- 在八个其余螺栓头下方涂覆工具 (B) 。 安装螺栓 (1) 并用手拧紧。
Show/hide table
图 8 | g02318815 |
- 确保螺栓头座合在四个埋头孔内。
Show/hide table
图 9 | g02319134 |
- 首先,以 A、B、C、D 的模式拧紧四个埋头螺栓。 将四个螺栓 (1) 上紧到 350 ± 50 N·m (258 ± 37 lb ft) 的扭矩。
- 按星形模式拧紧其余的 8 个螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 350 ± 50 N·m (258 ± 37 lb ft)。
- 按同样的模式再次拧紧螺栓。 拧紧所有螺栓 (1) 至扭矩为 700 ± 50 N·m (516 ± 37 lb ft)。
Caterpillar Information System:
C9 Generator Set Engines Diagnostic Code Cross Reference
Bench Test Procedure for TH48FT - E80 Oil Field Transmission{3030, 3073, 3101} Bench Test Procedure for TH48FT - E80 Oil Field Transmission{3030, 3073, 3101}
C32 Petroleum Engines Cylinder Head - Remove
C27 and C32 Generator Set Engines Engine Temperature Sensor Open or Short Circuit - Test
315D, 318D and 319D Excavators Machine Systems Auxiliary Pilot Valve (Straight Travel) - Install
C27 and C32 Generator Set Engines Engine Pressure Sensor Open or Short Circuit - Test
3412 Generator Set Engines Fuel Shutoff Solenoid
Reuse and Salvage for 3000 Engine Series Cylinder Blocks {1201} Reuse and Salvage for 3000 Engine Series Cylinder Blocks {1201}
C175-16 and C175-20 Engines for Caterpillar Built Machines Valve Lifter - Assemble
C1.5 and C2.2 Generator Set Engines Radiator - Remove and Install
3508 EUI Engine for D11N and D11R Track-Type Tractors Installation and Removal of the Speed/Timing Sensor
C32 Petroleum Engines Valve Mechanism Cover - Remove and Install
C27 and C32 Generator Set Engines Coolant Level Sensor Circuit - Test
3500 Marine Engines Pistons, Rings and Connecting Rods
2005/09/26 A New Fuel Lift Pump is Now Available {1256, 1258}
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Auxiliary Water Pump - Disassemble
2005/10/03 A New Retaining Plate and Bolts for the Bushing on the Engine Idler Gear are Now Available {1151, 1210, 1234}
C9 Generator Set Engines System Configuration Parameters
2005/09/26 New Turbocharger Water Lines are now Used {1380}
C4.4 and C6.6 Engines Event Codes
C9 Marine Engines System Overview
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Track - Separate - Non-PPR2
C27 and C32 Engines General Information
C175 Generator Set Engines Turbocharger - Remove