Calibration Error Codes
General Calibration Error Codes
Show/hide table
Error Codes That Can Be Activated When Any General Calibration Procedures Are Performed | ||
---|---|---|
Error Code | Probable Cause of Activation | Recommended Actions |
0002 - Active Diagnostic Present | An active diagnostic is preventing the calibration from being performed successfully. | · An active diagnostic code for any of the following will inhibit a calibration: - An active diagnostic code for the solenoid that is being calibrated other than an FMI 13. · Resolve the problem that is causing the active diagnostic code. Then retry the calibration. |
0003 - Another Calibration Is Active | · A calibration procedure is trying to run on the Monitoring System Display and Cat® Electronic Technician (Cat ET) Service Tool at the same time. OR A calibration was started and did not successfully close out. |
· Only perform one calibration procedure at a time. · If a calibration is canceled, wait at least 15 seconds before starting another calibration procedure. · If the error message continues to pop up, key OFF and back ON before attempting the calibration again. |
0004 - Calibration Active By Another ECM | A calibration procedure is trying to run on the Monitoring System Display and Cat ET at the same time. OR A calibration was started, then canceled and another calibration is started too fast. |
· Only run one calibration procedure at a time. · If one calibration is canceled, wait at least 15 seconds before starting another calibration procedure. |
0005 - Loss Of Calibration Interlock | Cat ET has lost communication with the ECM. | · Check for any active Cat Data Link diagnostic codes. Resolve any active codes. · Check the Cat Data Link Connections. · Check the Cat ET communication connections. · Cycle the key start switch from ON to OFF, wait 10 seconds, then turn the key start switch to ON. Perform the calibration procedure again. |
0006 - Calibration Aborted By Tool / Monitor | The calibration has been canceled by the user in Cat ET or in the Monitor | · Cancellation may cause activation of the 0006 error code. · Wait at least 15 seconds before performing another calibration. |
000B - Calibration Not Supported | Incorrect / early version of Cat ET is used that does not support the calibration. Incorrect flash file is downloaded into the ECM Machine is not equipped for this calibration |
· Ensure that the latest version of Cat ET is installed on your PC. · Verify that the correct flash file is downloaded into the ECM. Note: After the ECM has been flashed, cycle the key start switch from ON to OFF. Wait 10 seconds, then turn the key start switch to ON. Rerun the calibration procedure. · Verify machine is properly equipped for calibration. |
Caterpillar Information System:
Assembly Procedure for the 442-4004 Bucket Gp and the 442-4005 Bucket Gp {6101} Assembly Procedure for the 442-4004 Bucket Gp and the 442-4005 Bucket Gp {6101}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261} 20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
C4.4 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install - Nitrogen Oxide Sensor Positioned in Original Equipment Manufacture (OEM) Exhaust Tube Assembly
Location of The 456-4554 Plate and Spacer Installation Gp {6547} Location of The 456-4554 Plate and Spacer Installation Gp {6547}
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Piston Pump (Ejector and Steering) - Remove and Install
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Piston Pump (Brake, Ejector and Fan) - Assemble
Location of The 456-4553 Plate and Spacer Installation Gp {6513, 6547} Location of The 456-4553 Plate and Spacer Installation Gp {6513, 6547}
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Window Wiper and Wiper Motor (Front) - Remove and Install
Location of The 456-4552 Plate and Spacer Installation Gp {6513, 6547} Location of The 456-4552 Plate and Spacer Installation Gp {6513, 6547}
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Piston Pump (Brake, Ejector and Fan) - Disassemble
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Piston Pump (Brake, Ejector and Fan) - Remove and Install
Location of The 456-4551 Plate and Spacer Installation Gp {6547} Location of The 456-4551 Plate and Spacer Installation Gp {6547}
E-series Hammer Improvements {6333} E-series Hammer Improvements {6333}
773GC Off-Highway Truck Machine System Position Sensor (Foot Brake Control)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Window Wiper and Wiper Motor (Rear) - Remove and Install
2014/10/15 A New 451-6380 Thumb Arrangement is Now Available for Certain Mini Hydraulic Excavators {6547}
Installation Procedure for the 462-1657 Coupler Control Ar on Certain Hydraulic Excavators {1408, 5057, 5133, 7301, 7405, 7557} Installation Procedure for the 462-1657 Coupler Control Ar on Certain Hydraulic Excavators {1408, 5057, 5133, 7301, 7405, 7557}
2014/10/08 New Dual Lock Tilt Coupler Operating Instructions are Available for Certain Mini Hydraulic Excavators {5063, 5705, 6107, 6129}
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Oil Sample - Obtain
725 C2 Articulated Truck LRC Engine Supplement Gear Motor (Hydraulic Fan) - Assemble
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Control Valve (Ejector) - Disassemble
725C2, 730C2 Ejector Articulated Trucks - Machine Systems Control Valve (Ejector) - Remove and Install
725 C2 Articulated Truck LRC Engine Supplement Gear Motor (Hydraulic Fan) - Disassemble
Installation of the 353-0768 Pilot Lines Gp on Certain Hydraulic Excavators{5057} Installation of the 353-0768 Pilot Lines Gp on Certain Hydraulic Excavators{5057}