Sprocket - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 8S-7640     | 台架     | 2     |
8S-7611 | 管     | 2     | |
8S-7615 | 销     | 2     | |
B     | 138-7574     | 连杆支架     | 1     |
开始:
- 分离履带。 请参阅拆解和组装, "履带 - 分离"。
- 如图所示,升起机器的侧面以便在机架下安装工具 (A) 。
Show/hide table
图 1 | g00489826 |
注: 调整工具 (A) 的高度以使链轮和履带之间留出的间隙足以从终传动上拆下链轮。
- 拆下将链轮 (2) 固定至终传动的螺栓 (1) 。
Show/hide table
图 2 | g00708732 |
- 将工具 (B) 和适当的起吊设备连接到链轮 (2) 上。 链轮 (2) 的重量约为 40 kg (88 lb)。
Show/hide table
图 3 | g00708688 |
注: 在工具 (B) 和链轮之间使用几个垫圈。 这将防止损坏链轮。
- 拆下链轮 (2) 。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 8S-7640     | 台架     | 2     |
8S-7611 | 管     | 2     | |
8S-7615 | 销     | 2     | |
B     | 138-7574     | 连杆支架     | 1     |
- 在安装链轮之前,彻底清洁链轮与终传动之间的配合面。
- 将工具 (B) 和适当的起吊设备连接到链轮 (2) 上。 链轮 (2) 的重量约为 40 kg (88 lb)。 安装链轮 (2) 。
Show/hide table
图 4 | g00708688 |
注: 在工具 (B) 和链轮之间使用几个垫圈。 这将防止损坏链轮。
- 安装用于将链轮固定在终传动上的螺栓 (1) 。 以交叉模式拧紧螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 530 ± 70 N·m (395 ± 50 lb ft)。
Show/hide table
图 5 | g00708732 |
- 提升机器。 从机架上拆下工具 (A) 和相应的起吊设备。
Show/hide table
图 6 | g00489826 |
End By: 连接履带组件。 请参阅 拆解和组装, "履带 - 连接"。
Caterpillar Information System:
Installation Procedure for 260-7984 Pilot Lines Gp (PILOT OIL PRESSURE){5057, 5059, 6307} Installation Procedure for 260-7984 Pilot Lines Gp (PILOT OIL PRESSURE){5057, 5059, 6307}
GLC85 Forestry Grapple Rotator Manifold Leakage - Test
GLC85 Forestry Grapple Hydraulic Rotator Cycle Time - Check
345C Excavator (Ultra High Demolition) Hydraulic System Control Valve (Stick Lowering)
GLC85 Forestry Grapple Rotator Manifold - Disassemble
GLC85 Forestry Grapple Rotator Manifold - Assemble
307D Excavator Machine Systems Undercarriage Frame - Remove
GLC85 Forestry Grapple Work Tool Preparation for Troubleshooting
307D Excavator Machine Systems Undercarriage Frame - Install
314D CR Hydraulic Excavator Machine Systems Main Control Valve - Assemble
2010/07/14 Correction to Testing and Adjusting , "Main Pump (Flow) - Test - Constant Horsepower Flow Control" for 315D and 319D Excavators {5070}
319D Excavator Machine System Specifications Bucket Linkage - Coupler
323D Excavator Lifting Capacities
315D and 318D Excavators Machine System Specifications Solenoid Valve (Swing Motor)
345C Excavator (Ultra High Demolition) Hydraulic System Cylinders (Boom, Stick and Bucket)
345C Excavator (Ultra High Demolition) Hydraulic System Swing Hydraulic System
C4.2 and C6.4 Engines for Caterpillar Built Machines Fuel Injection Pump
2008/08/11 New C18 Cylinder Liners and O-ring Seals are Used {1201, 1216, 1216}
307D Excavator Engine Supplement Alternator - Remove and Install
345C Excavator (Ultra High Demolition) Hydraulic System Travel Hydraulic System
323D MHPU Mobile Hydraulic Power Unit Securing the Machine
307D Excavator Engine Supplement Refrigerant Compressor - Remove and Install
2008/08/11 Procedure is Available to Improve the Mounting Locations of the Grab Handle. {7301}
307D Excavator Machine Systems Check Valve (Cooler Bypass) - Remove