Camshaft Speed Sensor - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-4030     | 螺纹锁固胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 卸下转速传感器的电源。
- 从计量泵 (4) 上卸下管组件 (5) 。
Show/hide table
图 1 | g00598375 |
- 从凸轮轴转速/正时传感器 (2) 上断开线束组件 (3) 。
- 松开螺母 (1) 。 卸下凸轮轴转速/正时传感器 (2) 。
- 转动发动机,将磁铁与凸轮轴盖的孔对齐。
- 卸下计量泵 (4) 。 拆下适配器 (6) 。
- 卸下磁铁(未显示)。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 转动发动机,将磁铁的位置与凸轮轴盖的孔对齐。
Show/hide table
图 2 | g00598375 |
- 将工具 (A) 涂敷在新磁铁上。 安装磁铁。
- 安装接头 (6) 。 确保磁铁与凸轮轴盖的孔对齐。
- 拧入凸轮轴转速/正时传感器 (2) ,直至传感器触碰磁铁。 然后将传感器转松 3/4 圈。
- 将锁紧螺母 (1) 拧紧至扭矩 45 ± 7 N·m (33 ± 5 lb ft)。
- 将线束组件 (3) 连接至凸轮轴转速/正时传感器 (2) 。
- 安装计量泵 (4) 和管组件 (5) 。
- 将电源连接至转速传感器。
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) For MUI Engines Troubleshooting Dedicated Shutdown Indicators
Electronic Modular Control Panel II (EMCP II) For MUI Engines AL Fault Code - Troubleshoot
Electronic Modular Control Panel II (EMCP II) For PEEC Engines SP Fault Code - Troubleshoot
3500B Engines and 3500 Engines with EUI Option Ether Injection System
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble - 3003 Engines
3064 and 3066 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
G3500 Engines Cylinder Head - Assemble
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 560 FMI 11 CAT Data Link Failure Mode Not Identified - Test
G3516B and G3520B Generator Set Engines Air Starting Motor - Assemble
3126B Marine Engine Electric Starting Motor
3500B Engines and 3500 Engines with EUI Option Prelubrication System
3034 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for Low Oil Pressure - Troubleshoot
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Flywheel
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Indicator for Emergency Stop - Troubleshoot
G3606 and G3608 Engines Caterpillar Ignition System (CIS) Module - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for High Water Temperature - Troubleshoot
G3606 and G3608 Engines Actuator (Hydrax) - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for Low Coolant Level - Troubleshoot
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Indicator for Overcrank - Troubleshoot
G3606 and G3608 Engines Actuator (Hydrax) - Assemble
Instructions For Correcting Speed Surge In 3406C PEEC III Truck Engines{1408} Instructions For Correcting Speed Surge In 3406C PEEC III Truck Engines{1408}
G3606 and G3608 Engines Actuator (Hydrax) - Install