Transmission (Direct Drive) - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-7640     | Stand     | 2     |
8S-7611 | Tube     | 2     | |
8S-7615 | Pin     | 2     | |
B     | 308-3471     | Jack Stand Gp     | 2     |
C     | 1U-7505     | Hydraulic Jack     | 1     |
D     | 1U-9754     | Hydraulic Jack     | 1     |
- Use Tooling (C ) to position the transmission (6) . The weight of transmission (6) is approximately 200 kg (441 lb).
Show/hide table
Illustration 1 | g03227979 |
- Install 12 bolts (15) .
Show/hide table
Illustration 2 | g03228117 |
- Position transmission filler tube (13) . Install two bolts (14) .
Show/hide table
Illustration 3 | g03228079 |
- Install bolt (12) .
- Connect hose assembly (11) .
Show/hide table
Illustration 4 | g03228036 |
- Connect hose assembly (9) .
Show/hide table
Illustration 5 | g03652281 |
- Install four bolts (109) .
- Repeat Step 7 for the opposite side.
- Slide rod assembly (8) on the transmission lever and tighten bolt (7) .
Show/hide table
Illustration 6 | g03652274 |
- Connect three harness assemblies (5) .
Show/hide table
Illustration 7 | g03227977 |
- Install plug (4) .
Show/hide table
Illustration 8 | g00762357 |
- Remove Tooling (D) .
Show/hide table
Illustration 9 | g03228120 |
- Install inspection plate (3) .
Show/hide table
Illustration 10 | g03227916 |
- Remove Tooling (B) from the front axle (2) .
Show/hide table
Illustration 11 | g00760890 |
- Remove Tooling (A) from the rear axle (1) .
Show/hide table
Illustration 12 | g00760888 |
- Fill the transmission with oil. Refer to Operation and Maintenance Manual, SEBU9921, "Transmission Oil - Change" for the proper filling procedure.
End By:
- Install the piston pump.
- Install the rear drive shaft.
Caterpillar Information System:
PL83 Pipelayer TA2 Technical Inspection{7000, 753T} PL83 Pipelayer TA2 Technical Inspection{7000, 753T}
2012/09/19 Improved Mounting Updates the Hoist Lines Group on 795F AC Off-Highway Truck {5057, 5057}
C175-16 and C175-20 Locomotive Engines Electronic Unit Injector Sleeve - Remove
Health Interface Module Setup and Configuration Guide Utilities Menu
Health Interface Module Setup and Configuration Guide Communicator Menu
Health Interface Module Setup and Configuration Guide GPS Menu
Health Interface Module Setup and Configuration Guide Device Menu
559C and 579C Knuckleboom Loaders Location of Components (HVAC System)
Health Interface Module Setup and Configuration Guide User Interface
C1.5 and C2.2 Engines for Caterpillar Built Machines Electronic Service Tools
Alternator - Bosch K1/N1 Alternator - Disassemble
2012/11/01 New Bellows Are Used for the Turbocharger Exhaust on C175-20 Off-Highway Truck Engines {1061}
2013/10/17 New Tube Assemblies are Available for the 797, and 797B Off-Highway Trucks {5056}
424B and 424B HD Backhoe Loaders Power Train Transmission (Direct Drive) - Disassemble
MH3049 Material Handler Hydraulic System Flow Diverter Valve (Optimal Turning) - Adjust
PL87 Pipelayer TA2 Technical Inspection{7000, 753T} PL87 Pipelayer TA2 Technical Inspection{7000, 753T}
Bronze 416-2492 Engine Overhaul Kit for 3176 Machine Engines{1000} Bronze 416-2492 Engine Overhaul Kit for 3176 Machine Engines{1000}
521B and 522B Track Feller Bunchers Machine Systems Travel Motor - Remove and Install
MH3049 Material Handler Hydraulic System Relief Valve (Hydraulic Oil Warming) - Test and Adjust
559C and 579C Knuckleboom Loaders Piston Pump (Implement)
Software Defect On the Cat® Detect Object Detection System Used On Certain Cat Machines{7620} Software Defect On the Cat® Detect Object Detection System Used On Certain Cat Machines{7620}
2012/09/28 A New Special Instruction to Install the Front Wheel Site Glass Retrofit Kit on Certain Off-Highway Trucks is Now Available {4006, 4205, 7479}
2012/09/19 New Adapter Bearing Is Now Used for Blower Fan Group on 795F AC Off-Highway Trucks {1636, 4017, 7551}
424B and 424B HD Backhoe Loaders Power Train Transmission (Direct Drive) - Assemble