Hook Winch Motor - Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
- Attach a suitable lifting device to hook winch motor (7). The weight of hook winch motor (7) is approximately
68 kg (150 lb) . Use the suitable lifting device in order to position hook winch motor (7) to the hook winch. - Install bolts (6).
Show/hide table
Illustration 2 g01619012 - Connect hose assemblies (5) and (4).
- Connect harness assembly (3).
- Connect hose assemblies (2) and (1).
Show/hide table
Illustration 1 | g01619026 |
End By:
- Install the boom winch drive motor. Refer to Disassembly and Assembly, "Winch Drive Motor - Install".
Caterpillar Information System:
793F CMD Off-Highway Truck Hydraulic Fan and Steering System Oil Filter (Rear Axle Lubrication)
773E Off-Highway Truck Drive Shaft Slip Joint - Lubricate
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1403 - FMI 06
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1403 - FMI 05
A New Retaining Method Is Available For The Boom Pivot Pin On Certain Telehandlers{5456} A New Retaining Method Is Available For The Boom Pivot Pin On Certain Telehandlers{5456}
773E Off-Highway Truck Specifications
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1403 - FMI 03
CD54 Vibratory Compactor Machine Systems Water Tank - Remove and Install
CD54 Vibratory Compactor Machine Systems Water Filter - Remove and Install
PL61 Pipelayer Machine Systems Hook Winch Motor - Remove
PL61 Pipelayer Machine Systems Boom Sheave Block (Lower) - Install
2008/07/28 A New Track Shoe is Now Used on Certain Cold Planers {4172}
PL61 Pipelayer Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1405 - FMI 03
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hydraulic Accumulator (Suspension) - Test and Charge
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1405 - FMI 05
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1405 - FMI 06
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1529 - FMI 02
Procedure for Checking the Electrical Circuit that is for the Actuator and the Water Valve{1812, 7304, 7320} Procedure for Checking the Electrical Circuit that is for the Actuator and the Water Valve{1812, 7304, 7320}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1529 - FMI 04
Field Installation of the Pin Retention System for the Hoist Cylinder on the 797 Off-Highway Truck{5102, 6068, 7562} Field Installation of the Pin Retention System for the Hoist Cylinder on the 797 Off-Highway Truck{5102, 6068, 7562}
2008/08/11 The Crankcase Breather for the Engine is Relocated {1107, 1157}
2008/08/11 An Improved Bracket Assembly Updates the Fan Drive Groups {1359}
MINEGEM Machine Control ; Guidance Products Circuit Breakers - Reset - R2900G JLK