Oil Filter (Rear Axle Lubrication)
Show/hide table
Illustration 1 | g01902813 |
Show/hide table
NOTICE |
---|
Do not use an air wrench in order to tighten the housing assembly. |
(1) 334-2679 Spring
- Length under test force ... 57.6 mm (2.268 inch)
- Test force ... 179.53 ± 8.98 N (40.360 ± 2.019 lb)
- Free length after test ... 85.6 mm (3.370 inch)
- Outside diameter ... 22.35 mm (0.880 inch)
- Test force ... 179.53 ± 8.98 N (40.360 ± 2.019 lb)
(2) 334-2680 Spring
- Length under test force ... 57.6 mm (2.268 inch)
- Test force ... 98.67 ± 4.93 N (22.182 ± 1.108 lb)
- Free length after test ... 68.2 mm (2.685 inch)
- Outside diameter ... 16.17 mm (0.637 inch)
- Test force ... 98.67 ± 4.93 N (22.182 ± 1.108 lb)
(3) Torque for sensor ... 80 ± 10 N·m (60 ± 7 lb ft)
(4) Lubricate the O-ring seal with the lubricant that is being filtered.
(5) Torque for base assembly ... 75 ± 5 N·m (55 ± 4 lb ft)
Note: After tightening base assembly (5) to 75 ± 5 N·m (55 ± 4 lb ft), rotate base assembly (5) counter clockwise 1/4 of a turn, and then rotate base assembly (5) clockwise 1/4 of a turn.
Caterpillar Information System:
773E Off-Highway Truck Drive Shaft Slip Joint - Lubricate
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1403 - FMI 06
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1403 - FMI 05
A New Retaining Method Is Available For The Boom Pivot Pin On Certain Telehandlers{5456} A New Retaining Method Is Available For The Boom Pivot Pin On Certain Telehandlers{5456}
773E Off-Highway Truck Specifications
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1403 - FMI 03
CD54 Vibratory Compactor Machine Systems Water Tank - Remove and Install
CD54 Vibratory Compactor Machine Systems Water Filter - Remove and Install
PL61 Pipelayer Machine Systems Hook Winch Motor - Remove
PL61 Pipelayer Machine Systems Boom Sheave Block (Lower) - Install
2008/07/28 A New Track Shoe is Now Used on Certain Cold Planers {4172}
2008/11/03 An Improved Cold Start Arrangement Is Available for some Track Feller Bunchers {1401, 1402, 1408, 1450, 1453, 7000, 7257}
PL61 Pipelayer Machine Systems Hook Winch Motor - Install
PL61 Pipelayer Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1405 - FMI 03
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hydraulic Accumulator (Suspension) - Test and Charge
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1405 - FMI 05
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1405 - FMI 06
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1529 - FMI 02
Procedure for Checking the Electrical Circuit that is for the Actuator and the Water Valve{1812, 7304, 7320} Procedure for Checking the Electrical Circuit that is for the Actuator and the Water Valve{1812, 7304, 7320}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Electronics and Electrical Systems MID 039 - CID 1529 - FMI 04
Field Installation of the Pin Retention System for the Hoist Cylinder on the 797 Off-Highway Truck{5102, 6068, 7562} Field Installation of the Pin Retention System for the Hoist Cylinder on the 797 Off-Highway Truck{5102, 6068, 7562}
2008/08/11 The Crankcase Breather for the Engine is Relocated {1107, 1157}
2008/08/11 An Improved Bracket Assembly Updates the Fan Drive Groups {1359}