Fuel Injection Pump Gear - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6198     | 曲轴转动工具     | 1     |
A (2)     | 9U-7336     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 230-6284     | 正时销(凸轮轴)     | 1     |
C     | 230-6283     | 正时销(曲轴)     | 1     |
D     | 1P-2320     | 组合式拉拔器     | 1     |
Show/hide table
( 1 ) | 曲轴转动工具用于前皮带轮。 |
( 2 ) | 该工具在电动起动马达的孔上使用。 |
开始:
- 拆下前盖。 请参阅拆解和组装, "前盖 - 拆卸和安装"。
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 必须小心操作,确保在燃油泵齿轮的拆卸过程中不会改变燃油泵正时。 小心地按照本步骤拆卸燃油泵齿轮。
- 使用工具 (A) 转动曲轴,使 1 号活塞处于其压缩冲程的上止点位置。 请参阅系统操作、测试和调整, "确定 1 号活塞上止点位置"。
- 将工具 (B) 穿过凸轮轴齿轮 (1) 的孔 (X) 安装到前壳体中。 使用工具 (B) 将凸轮轴锁定到位。
Show/hide table
图 1 | g01343056 |
典型示例 |
- 将工具 (C) 安装到前壳体的孔 (Y) 中。 使用工具 (C) 将曲轴锁定到位。
注: 安装工具 (C) 时不要使用过大的力量。 在修理过程中不要使用工具 (C) 固定曲轴。
- 逆时针方向向喷油泵齿轮 (3) 施加足够的压力来消除齿隙。 将喷油泵 (4) 锁定在此位置。 松开锁定螺钉 (5) 。 转动隔套 (6) ,以便将锁定螺钉 (5) 拧紧抵到喷油泵的轴上。 拧紧锁定螺钉 (5) 至扭矩为 17 N·m (13 lb ft)。
注: 必须拧紧锁定螺钉 (5) ,以防喷油泵的轴发生转动。 从发动机上卸下喷油泵后不能使喷油泵的轴转动。
Show/hide table
图 2 | g01320304 |
- 标记齿轮 (1) 、 (2) 和 (3) 以便可以显示对准位置。 参考图 3。
注: 识别标记能确保将齿轮安装在原来的对准位置。
Show/hide table
图 3 | g01335384 |
正时标记的对准 |
- 松开燃油泵齿轮 (3) 上的螺母。
- 将工具 (D) 穿过燃油泵齿轮 (3) 中的三个孔安装。 拧紧工具 (D) 直至松开燃油泵齿轮。
- 将工具 (D) 从燃油泵齿轮 (3) 上卸下。
- 将螺母和垫圈从燃油泵齿轮 (3) 上卸下。 卸下燃油泵齿轮。
Caterpillar Information System:
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Install
C6.6 Engines For Caterpillar Built Machines CID 2417 FMI 06
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Remove
C6.6 Engines For Caterpillar Built Machines CID 2417 FMI 05
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector Cover - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Lines - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Priming Pump and Fuel Filter Base - Remove and Install
2007/05/28 An Improved Battery Isolation Control is Now Used {1402, 1408}
2009/08/24 An Improved Solenoid Valve Group Is Used In Transmissions With ICM For Increased Reliability And Longer Service Life {3124, 3167, 3174}
IT38H Integrated Toolcarrier and 938H Wheel Loader Steering System Secondary Steering System
2007/08/27 A New Temperature Gauge is Used {7450}
16M Motor Grader Machine Systems Front Frame to Rear Frame (Articulating Hitch) - Connect
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Pump Gear - Install
C6.6 Engines For Caterpillar Built Machines CID 2770 FMI 03
770 and 772 Off-Highway Trucks Engine Supplement Alternator - Remove and Install
Test and Repair for Excessive Current Draw{1401, 1408} Test and Repair for Excessive Current Draw{1401, 1408}
2007/08/06 New Water Lines Groups Are Available {1380}
2007/06/04 An Enhanced Diagnostic Procedure is Now Available for the Air Conditioner Dryer {7322}
450E Backhoe Loader Machine Systems Lift Arms - Remove
587R Pipelayer Engine Supplement Fan and Fan Drive - Remove and Install
770 and 772 Off-Highway Trucks Engine Supplement Disconnect Switch (Battery) - Remove and Install
2007/08/06 An Improved Left Side Alternator Guard is Used {7174}
CS54 and CP54 Vibratory Soil Compactors Sound Information and Vibration Information
CS54 and CP54 Vibratory Soil Compactors Specifications