Service Interval Chart
欲知更多的保养资料,请查阅下面的保养周期图表和保养周期。
246C和 256C
Show/hide table
图 1 | g01275402 |
262C和 272C
Show/hide table
图 2 | g01275403 |
保养周期
Show/hide table
冷却液添加剂 - 每工作 6000 小时,或者每 3 年,往长效冷却液里添加延长剂。 |
Show/hide table
冷却液液位(散热器) - 每工作十小时,或者每天收工时,通过观测窗检查散热器中冷却液的液位。 |
Show/hide table
冷却液液位(储液罐) - 每工作十小时,或者每天收工时, 检查冷却液储液罐中冷却液的液位。 |
Show/hide table
冷却系统的冷却液 - 每工作 12,000 小时,或者每 6 年,更换长效冷却液(ELC)。 |
Show/hide table
驱动链箱油 - 每工作 1,000小时或每6个月后更换 驱动链箱油。 |
Show/hide table
发动机空气滤清器的粗滤芯 - 清洁空气滤清器粗滤芯或更换空气滤清器粗滤芯。 空气滤清器的报警器指示需要保养。 |
Show/hide table
发动机空气滤清器细滤芯 - 每当第三次更换空气滤清器粗滤芯时,更换空气滤清器的细滤芯,或者在必要时更换空气滤清器的细滤芯。 |
Show/hide table
发动机机油油位检查 - 每工作十小时,或者每天收工时, 检查发动机机油油位。 |
Show/hide table
发动机机油 - 每工作 500 小时或者每年,更换一次发动机机油。 |
Show/hide table
发动机机油滤清器 - 每工作 500 小时或者每三个月要更换滤清器。 |
Show/hide table
燃油系统油水分离器 - 每工作十小时,或者每天收工时, 要排放油水分离器。 |
Show/hide table
燃油系统滤清器/油水分离器芯 - 每工作 500 小时,或者每三个月更换滤清器。 |
Show/hide table
黄油嘴 - 每工作十小时,或者每天收工时,要对指明部位进行润滑。 |
Show/hide table
液压油滤清器 - 每工作 500 小时或者每三个月要更换滤清器。 |
Show/hide table
液压系统油位检查 - 每工作十小时,或者每天收工时, 通过观测窗检查液压系统的油位。 |
Show/hide table
液压油 - 每工作 2000 小时或者每年,更换液压油一次。 |
Caterpillar Information System:
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System General Information
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Final Drive Oil Level - Check
277C, 287C and 297C Multi Terrain Loaders Final Drive Oil - Change
773F, 773F OEM, 777F and 777F OEM Off-Highway Trucks and 775F and 775F OEM Quarry Truck Vital Information Management System (VIMS) General Information
Filtration Procedure for Articulated Truck Steering Oil {0680, 0768, 4304, 4332, 5056, 5057} Filtration Procedure for Articulated Truck Steering Oil {0680, 0768, 4304, 4332, 5056, 5057}
Bench Test Procedure For A 768C, 769C, 772B, and 773B Off-Highway Truck Torque Converter{3101, 3133} Bench Test Procedure For A 768C, 769C, 772B, and 773B Off-Highway Truck Torque Converter{3101, 3133}
2007/01/15 A New Speed-Timing Sensor is Available {1912}
12H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Solenoid Valve (Centershift Lock)
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Pitch Cylinder (3-Point Hitch)
2006/08/21 A Improved Alternator Guard is Used {7310}
AccuGrade® GPS GPS Accuracy Mode - Set - GPS Accuracy Option
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Relief Valve (Torque Converter Inlet)
277C, 287C and 297C Multi Terrain Loaders Service Interval Chart
2006/11/27 The New Bevel Gears Improve Reliability {3159, 3256, 3258, 3270}
Failures in Hardware in VIMS ECM{7601} Failures in Hardware in VIMS ECM{7601}
2010/03/04 Orifices in the Brake Lines Improve the Performance of the Pressure Switches {1408, 4282, 4284}
2006/10/30 An Improved Muffler is Now Available for Soil Compactors {1062}
2006/10/09 New Ball Studs Improve the Service Life of the Steering Cylinders and the Steering Linkages {4303, 4305}
C15 and C18 Petrolem Generator Set Engines Welding Precaution
Failure of the Detent Coil Wire on Skid Steer Loaders and Multi Terrain Loaders with Dual Direction Control{5059, 5705} Failure of the Detent Coil Wire on Skid Steer Loaders and Multi Terrain Loaders with Dual Direction Control{5059, 5705}
C15 and C18 Petrolem Generator Set Engines Diagnostic Capabilities
216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders, 247B3 and 257B3 Multi Terrain Loaders and 259B3 Compact Track Loader Engine Starting
C15 and C18 Petrolem Generator Set Engines Programmable Parameters
2006/10/16 New Hose Clamps Are Used on the Air Induction System For Pneumatic Compactors {1071}