Wheel Lean Bar - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A(1) | 9U-7536 | Lift Stand | 1 |
| 447-0910 | Electric Hydraulic Pump Gp (115 V) | 1 | |
| 447-0911 | Electric Hydraulic Pump Gp (230 V) | 1 | |
| A1 | OR | ||
| 504-9791 | Lift Gp (60Hz)(2) | 1 | |
| 504-9793 | Lift Gp (50Hz)(3) | 1 | |
| B | 1P-1832 | Bearing Pulling Adapter | 1 |
| 4C-9633 | Puller Stud | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 5F-7353 | Washer | 1 | |
| 9U-6833 | Nut | 1 | |
Show/hide table
| (1) | Use Tooling (A) or (A1) based on requirements. |
| (2) | Operating Voltage (240 - 480V) |
| (3) | Operating Voltage (200 - 400V) |
- Use Tooling (A) to support front axle (1).
Show/hide table
Illustration 2 g06363496 For Tooling (A1). - Position Tooling (A1) as shown. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
- Use Tooling (A1) to support front axle (1).
Show/hide table
Illustration 3 g01380749 Show/hide table
Illustration 4 g01380763 - Attach a suitable lifting device to both ends of wheel lean bar (2). The weight of wheel lean bar (2) is approximately
68 kg (150 lb) . - Remove bolt (3) and retainer (4).
- Repeat Step 5 for the opposite end of wheel lean bar (2).
- Remove wheel lean bar (2) from the wheel lean arms . Allow wheel lean bar (2) to rest on front frame (1).
- Remove the lifting device from the right side of wheel lean bar (2).
- Remove wheel lean bar (2).
Show/hide table
Illustration 5 g01380764 - Remove lip seals (5).
Show/hide table
Illustration 6 g06363056 - Use Tooling (B) to remove bearing (6). Repeat this step for the remaining bearing.
- Repeat Steps 10 and 11 for the opposite end of the wheel lean bar (2).
Show/hide table
| |
| Illustration 1 | g01346308 |
|
For Tooling (A). | |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A(1) | 9U-7536 | Lift Stand | 1 |
| 447-0910 | Electric Hydraulic Pump Gp (115 V) | 1 | |
| 447-0911 | Electric Hydraulic Pump Gp (230 V) | 1 | |
| A1 | OR | ||
| 504-9791 | Lift Gp (60Hz)(2) | 1 | |
| 504-9793 | Lift Gp (50Hz)(3) | 1 | |
| B | 1P-1832 | Bearing Pulling Adapter | 1 |
| 4C-9633 | Puller Stud | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 5F-7353 | Washer | 1 | |
| 9U-6833 | Nut | 1 | |
| C | 1P-0510 | Driver Gp | 1 |
Show/hide table
| (1) | Use Tooling (A) or (A1) based on requirements. |
| (2) | Operating Voltage (240 - 480V) |
| (3) | Operating Voltage (200 - 400V) |
- Use Tooling (B) to install bearing (6). Repeat this step for the remaining bearing.
Show/hide table
Illustration 8 g01380764 - Use Tooling (C) to install lip seals (5). Repeat this step for the remaining lip seals.
Show/hide table
Illustration 9 g01380763 Show/hide table
Illustration 10 g01380749 - Attach a suitable lifting device to install wheel lean bar (2). The weight of wheel lean bar is approximately
68 kg (150 lb) . - Position wheel lean bar (2) on the machine. Allow wheel lean bar (2) to rest on front frame (1). Attach a second suitable lifting device on wheel lean bar (2).
- Install wheel lean bar (2) on the wheel lean arms.
- Install retainer (4) and bolt (3).
- Repeat Step 6 for the opposite end of wheel lean bar (2).
Show/hide table
Illustration 11 g06363496 For Tooling (A1). - Remove Tooling (A1) from front axle (1). Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
Show/hide table
Illustration 12 g01346308 For Tooling (A). - Remove Tooling (A) from front axle (1).
Show/hide table
| |
| Illustration 7 | g06363056 |
Caterpillar Information System:
Test Sequence for Capsule Type Fuel Nozzles{0782} Test Sequence for Capsule Type Fuel Nozzles{0782}
14H Motor Grader Machine Systems Blade Lift Cylinder - Remove and Install
CB-634D Paving Compactor Machine Electronic Control System Service Tools
574B Forwarder Power Train On/Off Switches
TH210 and TH215 Telehandlers Power Train Parking Brake Control - Remove and Install
D350E and D400E Articulated Trucks Power Train Solenoid Valve (Lockup Clutch)
D350E and D400E Articulated Trucks Power Train Lockup Clutch and Solenoid Valve
574B Forwarder Power Train Accelerator Pedal
3054E Industrial Engine Camshaft Bearings - Remove and Install
D350E and D400E Articulated Trucks Power Train Priority Valve
793C and 793C XQ Off-Highway Truck Steering System Steering Linkage and Cylinder Mounting
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks ECM Output Circuit (Engine Coolant Temperature Lamp)
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070} Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070}
2002/10/28 Correction to Operation and Maintenance Manual , "Equipment Lowering with Engine Stopped" {7000}
2002/10/21 A Special Instruction, REHS1252, "Field Installation of Body Exhaust Arrangements" Is Available {1061, 7258}
14H Motor Grader Machine Systems Combination Valve - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Pump Control (Output Flow) - Adjust
14H Motor Grader Machine Systems Bank Valve - Remove
14H Motor Grader Machine Systems Bank Valve - Install
14H and 16H Motor Graders Hydraulic and Steering System Hydraulic Schematic
2002/10/28 Examine Failed Starting Motors to Understand the Reason for Failure {1453}
AP-655C and BG-2255C Asphalt Pavers Propel System Pressure Limiter Valve - Test and Adjust
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System Test/Enable Switch