Bank Valve - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | FT-1114 | Vacuum Cap | 1 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Use two people to install bank valve (11). The weight of bank valve (11) is approximately
37 kg (82 lb) . Install bolt (10). Tighten bolt (10) to a torque of60 ± 12 N·m (44 ± 9 lb ft) .Show/hide tableIllustration 2 g00931776 - Connect hose assembly (9).
Show/hide table
Illustration 3 g00931773 - Install bolts (8). Tighten bolt (8) to a torque of
60 ± 12 N·m (44 ± 9 lb ft) .Show/hide tableIllustration 4 g00931772 - Connect ten hose assemblies (7).
Show/hide table
Illustration 5 g00931769 - Install cover (5).
Show/hide table
Illustration 6 g00931766 - Connect linkages (6).
Show/hide table
Illustration 7 g00931755 - Move floormat (4) in position over cover (5).
Show/hide table
Illustration 8 g00931753 - Install bolts (3).
Show/hide table
Illustration 9 g00931752 - Slide cover (2) downward and install screws (1).
Show/hide table
Illustration 10 g00932648 - Remove Tooling (A) from the hydraulic tank.
- Fill the implement hydraulic system. Refer to the appropriate Operation and Maintenance Manual for the correct procedure.
Show/hide table
Illustration 1 | g00931779 |
Caterpillar Information System:
14H Motor Grader Machine Systems Bank Valve - Remove
TK711, TK721, TK722 and TK732 Track Feller Bunchers Hydraulic System Pump Control (Output Flow) - Adjust
14H Motor Grader Machine Systems Combination Valve - Remove
2002/10/21 A Special Instruction, REHS1252, "Field Installation of Body Exhaust Arrangements" Is Available {1061, 7258}
2002/10/28 Correction to Operation and Maintenance Manual , "Equipment Lowering with Engine Stopped" {7000}
Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070} Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070}
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
14H Motor Grader Machine Systems Wheel Lean Bar - Remove and Install
Test Sequence for Capsule Type Fuel Nozzles{0782} Test Sequence for Capsule Type Fuel Nozzles{0782}
14H Motor Grader Machine Systems Blade Lift Cylinder - Remove and Install
CB-634D Paving Compactor Machine Electronic Control System Service Tools
574B Forwarder Power Train On/Off Switches
14H and 16H Motor Graders Hydraulic and Steering System Hydraulic Schematic
2002/10/28 Examine Failed Starting Motors to Understand the Reason for Failure {1453}
AP-655C and BG-2255C Asphalt Pavers Propel System Pressure Limiter Valve - Test and Adjust
938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System Test/Enable Switch
574B Forwarder Power Train Introduction
C15 Petroleum Generator Set Engines Electric Starting Motor
3126B Machine Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
AP-655C and BG-2255C Asphalt Pavers Drag Conveyor and Auger Conveyor Systems Piston Pump Flow - Test - Upper and Lower Pump Stacks
2002/10/28 Systems Operation/Testing and Adjusting, SENR1456, "793C and 793C XQ Off-Highway Truck Suspension Cylinders" has been Revised {7201}
14H and 16H Motor Graders Air System and Brakes Quick-Release Valve
3054E Industrial Engine Flywheel - Remove
TH210 and TH215 Telehandlers Machine Systems Fender - Remove and Install