Addition to Testing and Adjusting , "Clutch Pedal - Adjust" {5157}
- Motor Grader:
- 14H (S/N: ASE1-UP; 7WJ1-UP)
- 16H (S/N: 6ZJ1-UP)
Add the following information.
"Clutch Pedal - Adjust"
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-7640     | Stand     | 1     |
8S-7611 | Tube     | 1     | |
8S-7615 | Pin     | 1     | |
B     | 1U-9745     | Air/Hydraulic Jack Gp     | 1     |
- Use Tooling (B) (not shown) in order to raise the machine. Install Tooling (A) below the main frame.
Show/hide table
Illustration 1 | g00588115 |
- As required, install cribbing under the tandems. The cribbing must prevent the tandems from oscillating in order to prevent the wheels from contacting the ground. The wheels must be prevented from contacting the ground during this procedure.
- Adjust rod ends (5) to dimension (B) .
Show/hide table
Illustration 2 | g00287631 |
Side View (1) Clutch pedal (2) Splined shaft (3) Stop screw (4) Floorplate (5) Rod end (two) (A) 95 ± 6 mm (3.7 ± 0.2 inch) (B) 447 ± 3 mm (17.6 ± 0.1 inch) |
- Position pedal (1) on splined shaft (2) to dimension (A) .
- Completely turn in stop screw (3) .
- Start the engine.
- Depress pedal (1). Put the transmission control lever in FIRST speed.
- Release pedal (1). Slowly depress pedal (1) until the wheels stop turning. Adjust stop screw (3) until the stop screw contacts pedal (1) .
- Put the transmission control lever in PARK position. Release pedal (1). Turn the stop screw (3) in one turn. Tighten the locknut.
- Push down on pedal (1). Put the transmission control lever in each forward and each reverse speed. If the wheels begin to move in any speed, loosen the locknut and turn stop screw (3) in one additional turn.
- Stop the engine.
- Raise the machine in order to remove Tooling (A) .
- Lower the machine.
Caterpillar Information System:
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Specifications
C4.4 Industrial Engine Aftercooler Core - Clean/Test - Air-To-Air Aftercooler
CB-434C Vibratory Compactor Rollover Protective Structure (ROPS) - Inspect
3524B Engine for Caterpillar Built Machines Engine Oil Pump - Disassemble
3524B Engine for Caterpillar Built Machines Engine Oil Pump - Assemble
3524B Engine for Caterpillar Built Machines Coupling Pump - Assemble
2002/07/15 Correction to Testing and Adjusting , "Rear Axle Housing End Play - Adjust" {3260}
3524B Engine for Caterpillar Built Machines Coupling Pump - Disassemble
Field Installation of the Engine Speed Control{1915} Field Installation of the Engine Speed Control{1915}
Bench Test Procedure for a 797 and 797B Off-Highway Truck Transmission {3030, 3073, 3139} Bench Test Procedure for a 797 and 797B Off-Highway Truck Transmission {3030, 3073, 3139}
Bench Test Procedure for a 797 and 797B Off-Highway Truck Torque Converter Inlet Relief Valve, Torque Converter Outlet Relief Valve, and Transmission Main Relief Valve {3030, 3101, 3133, 3210} Bench Test Procedure for a 797 and 797B Off-Highway Truck Torque Converter Inlet Relief Valve, Torque Converter Outlet Relief Valve, and Transmission Main Relief Valve {3030, 3101, 3133, 3210}
TH210 and TH215 Telehandlers Machine Systems Boom - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Flywheel Housing
3512 and 3516 EUI Engines and 784B, 785B, 789B and 793B Off-Highway Truck/Tractors Coolant Flow Switch
CB-434C Vibratory Compactor Steering Cylinder Ends - Lubricate
24H Motor Grader Final Drive Lip Seal - Replace
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Pulley
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 0668 - FMI 02
2002/07/22 The Engine Oil Recommendation for 3500 Series Diesel Engines has Changed {1000, 7560}
784C and 785C Off-Highway Truck/Tractors Air System and Brakes Slack Adjuster (Rear)
3056E Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Glow Plugs
267, 277 and 287 Multi Terrain Loaders Machine Systems Hydrostatic System Troubleshooting
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors CID 1682 FMI 02 Idle Shutdown Timer Switch loss of signal