Balancer Group - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 1P-0510 | 起子总成 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 利用四条螺栓 (1) 将轴 ( 2) 安装到缸体上。
Show/hide table
图 2 g00832534 (3) 平衡齿轮
(4) 轴承
(X) 20 度
(Y) 重心
(Z) 轴承内的接头Show/hide table图 3 g00833557 (3) 平衡齿轮
(4) 轴承
(T)1.3 mm (0.05 in) - 利用工具 (A) 将新轴承 ( 4) 安装到平衡齿轮 ( 3) 中。 安装轴承,使轴承内的接头 ( Z) 位于齿轮配重侧中心线 ( Y) 20 度的范围内。 将轴承压入平衡齿轮 ( 3) 的孔中,使其距离平衡齿轮 ( 3) 的对面
1.3 mm (0.05 in) 。 请参阅插图 3。Show/hide table图 4 g00833325 - 将干净的机油涂抹到平衡齿轮 ( 3) 内轴承的内表面上。 安装平衡齿轮 (3) 和板 ( 6)。 确保平衡齿轮带有配重的一侧面向缸体。 安装螺栓 (5)。 检查平衡齿轮的轴向间隙。 轴向间隙应当在
0.15 mm (0.006 in) 和0.36 mm (0.014 in) 之间。Show/hide table注意 安装中,确保平衡齿轮和凸轮轴后齿轮上的正时标记间对齐。
如果正时标记不对齐,可导致发动机损坏。
Show/hide table图 5 g00833461 - 将凸轮轴后齿轮 ( 7) 安装到凸轮轴上。 确保 "v" 形标记 (9) 对齐。 安装螺栓 (8)。 用
27 ± 4 N·m (20 ± 3 lb ft) 的扭矩拧紧螺栓 ( 8)。
Show/hide table
图 1 | g00833332 |
结束:
- 安装飞轮壳。 请参阅 拆解和组装, "飞轮壳体 - 拆卸和安装"。
Caterpillar Information System:
3408E and 3412E Engines for Caterpillar Built Machines Balancer Group - Remove
CP-563C and CS-563C Vibratory Compactors Final Drive Planetary (Drum) Oil - Check
3408E Engine Supplement for 769D Off-Highway Trucks and 771D Off-Highway Quarry Trucks Radiator - Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Temperature Switch (Axle Oil)
CP-563C and CS-563C Vibratory Compactors Final Drive Planetary (Drum) Oil - Change
CP-563C and CS-563C Vibratory Compactors Final Drive Planetary (Axle) Oil Sample - Obtain
CP-563C and CS-563C Vibratory Compactors Final Drive Planetary (Axle) Oil Level - Check
3408E Engine Supplement for 769D Off-Highway Trucks and 771D Off-Highway Quarry Trucks Fan Drive - Install
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0418 - FMI 03
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Transmission Oil Level - Check
CP-563C and CS-563C Vibratory Compactors Final Drive Planetary (Axle) Oil - Change
TL5 Series Field Cultivator Troubleshooting
TH350B, TH355B, TH360B and TH460B Telehandlers Battery Disconnect Switch - If Equipped
740 and 740 EJECTOR Articulated Trucks Power Train Output Transfer Gears - Assemble
TL5 Series Field Cultivator Transporting the Implement
2001/11/26 New Control Software for the Chassis ECM is Used {7620}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0418 - FMI 05
3408E Engine Supplement for 769D Off-Highway Trucks and 771D Off-Highway Quarry Trucks Engine and Torque Converter - Install
950G Series II Wheel Loader and 962G Series II Wheel Loader Electrohydraulic System Ride Control Accumulator - Test and Charge
A Process is Available to Replace the Propel Lever Group{3209, 5462} A Process is Available to Replace the Propel Lever Group{3209, 5462}
TL5 Series Field Cultivator Bearings - Lubricate
TL5 Series Field Cultivator Hydraulic Cylinders - Phasing
2001/11/19 New Clutch Discs with Improved Friction Material are Used for Improved Service Life {3030, 3160, 3187}
TK1051 Track Feller Buncher Window (Side Sliding)