Water Temperature Regulator - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1) and water temperature regulator (2) from the cylinder head.
Note: Note the orientation of the water temperature regulator.
Show/hide tableIllustration 2 g06327423 - Remove seal (3) from water temperature regulator (2).
Show/hide table
Illustration 1 | g06327422 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that all components of water temperature regulator (2) are clean and free of wear or damage.
- Check water temperature regulator 2 for correct operation. Refer to Testing and Adjusting, "Water Temperature Regulator - Test" for the procedure to test water temperature regulator (2). If any components of water temperature regulator (2) are worn or damaged, the complete assembly must be replaced.
- Thoroughly clean the gasket surface of the cylinder head.
- If the original water temperature regulator (2) is installed, position a new O-ring seal (3) into the groove in water temperature regulator (2).
Note: A new water temperature regulator is supplied with a new O-ring seal.
Show/hide tableIllustration 4 g06327422 - Install water temperature regulator (2) and bolts (1) to the cylinder head.
Note: Ensure the correct orientation of the water temperature regulator.
- Tighten bolts (1) to a torque of
44 N·m (32 lb ft) .
Show/hide table
Illustration 3 | g06327423 |
Caterpillar Information System:
320D3 and 323D3 Excavators Machine Electronic Control System System Schematic
C7.1 (Mechanical) Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7.1 (Mechanical) Engines for Caterpillar Built Machines Housing (Front) - Install
C7.1 (Mechanical) Engines for Caterpillar Built Machines Housing (Front) - Remove
C7.1 (Mechanical) Engines for Caterpillar Built Machines Idler Gear - Install
Procedure for Installing a Beacon Relay on Certain 320, 323, 330, and 336 Excavators {1408, 1431, 7301} Procedure for Installing a Beacon Relay on Certain 320, 323, 330, and 336 Excavators {1408, 1431, 7301}
340 Excavator Maintenance Interval Schedule
Track Shoe Ice Lug Requirements {4170} Track Shoe Ice Lug Requirements {4170}
The Steering Lines Group is Improved on Certain 797 Off-Highway Trucks {4304} The Steering Lines Group is Improved on Certain 797 Off-Highway Trucks {4304}
340 Excavator Engine Valve Lash - Check
340 Excavator System Pressure Release
340 Excavator Declaration of Conformity
C9.3 Industrial Engine Product Description
320D3 and 323D3 Excavators Machine Electronic Control System System Schematic
320D3 and 323D3 Excavators Machine Electronic Control System General Information
320D3 and 323D3 Excavators Machine Electronic Control System Engine Speed Control - Test
320D3 and 323D3 Excavators Machine Electronic Control System Relay - Test
C7.1 (Mechanical) Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C7.1 (Mechanical) Engines for Caterpillar Built Machines Alternator - Remove and Install
C9.3 Industrial Engine ARD Spark Plug - Clean - Emission Related Component
C9.3 Industrial Engine Diesel Exhaust Fluid - Fill - Emission Related Component
C9.3 Industrial Engine Diesel Exhaust Fluid Filter - Replace - Emission Related Component
C9.3 Industrial Engine Fluid Recommendations
C7.1 (Mechanical) Engines for Caterpillar Built Machines Engine Oil Pan - Remove