Vibration Damper and Pulley - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Description | Qty |
| A | - | Loctite Graphite-50 Anti-Seize Lubricant | - |
Start By:
- Remove damper guard. Refer to Disassembly and Assembly, Damper Guard - Remove and Install.
- Remove bolts (1) and pulley (2).
Show/hide table
Illustration 2 g06319798 - Remove belt (3). Refer to Operation and Maintenance Manual, Alternator Belt - Inspect/Adjust/Replace.
Show/hide table
Illustration 3 g06319846 - Remove nuts (4).
Show/hide table
Illustration 4 g06319863 - Use a suitable lifting device and remove damper assembly (5). The weight of damper assembly (5) is approximately
34 kg (75 lb) .Show/hide table
Illustration 5 g06319871 - Remove spacer (6) and crankshaft pulley (7).
Show/hide table
Illustration 6 g06319880 - Use a suitable lifting device and remove damper assembly (8). The weight of damper assembly (8) is approximately
34 kg (75 lb) .Show/hide table
Illustration 7 g06319897 - Remove studs (9) and bolts (10).
- Remove damper adapter (11).
Show/hide table
| |
| Illustration 1 | g06319793 |
- Apply Tooling (A) to bolts (10). Install damper adapter (11) and bolts (10).
- Install studs (11). Tighten to a torque of
65 ± 10 N·m (48 ± 7 lb ft) .Show/hide table
Illustration 9 g06319880 - Attach a suitable lifting device to damper assembly (8) and install on studs. The weight of damper assembly (8) is approximately
34 kg (75 lb) .Show/hide table
Illustration 10 g06319871 - Install crankshaft pulley (7) and spacer (6) on studs.
Show/hide table
Illustration 11 g06319863 - Attach a suitable lifting device to damper assembly (5) and install on studs. The weight of damper assembly (5) is approximately
34 kg (75 lb) .Show/hide table
Illustration 12 g06319846 - Install nuts (4). Tighten nuts (4) to a torque of
135 ± 20 N·m (100 ± 15 lb ft) .Show/hide table
Illustration 13 g06319798 - Install belt (3). Refer to Operation and Maintenance Manual, Alternator Belt - Inspect/Adjust/Replace.
Show/hide table
Illustration 14 g06319793 - Install pulley (2) and bolts (1). Tighten bolts to a torque of
135 ± 20 N·m (100 ± 15 lb ft) .
Show/hide table
| |
| Illustration 8 | g06319897 |
Caterpillar Information System:
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankshaft Rear Seal - Remove and Install
C18 Generator set and C18 Marine Engines Electronic Control Module - Remove and Install
G3500H Generator Set Engine Restriction of Air Inlet and Exhaust
C18 Generator set and C18 Marine Engines Electric Starting Motor - Remove and Install
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Prepare the Machine for Maintenance
C18 Generator set and C18 Marine Engines Coolant Temperature Sensor - Remove and Install
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Product Description
320D3 and 323D3 Excavators Machine System Specifications Final Drive
C18 Generator set and C18 Marine Engines Fuel Pressure Sensor - Remove and Install
320D3 Hydraulic Excavator Engine Supplements Exhaust Elbow - Remove and Install
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Engine Mounted Oil Filtered Base
C175 Tier 4 Final Engines for Caterpillar Built Machines Fuel and Auxiliary Water Pump Drive - Remove and Install
784C and 785C Off-Highway Truck/Tractors Machine Storage
A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057} A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057}
Software Update is Now Used on Certain 3500 Engines {1920} Software Update is Now Used on Certain 3500 Engines {1920}
Documentation Required for C175 Machine Engines that Experience Unexpected Engine Shutdowns {1000, 7418, 7760} Documentation Required for C175 Machine Engines that Experience Unexpected Engine Shutdowns {1000, 7418, 7760}
3500C IMO III Engines Sensor Signal (Analog, Active) - Test
Aftercoolers May be Missing the Internal Baffle on Certain 3500 Engines {1063, 1063} Aftercoolers May be Missing the Internal Baffle on Certain 3500 Engines {1063, 1063}
G3500H Generator Set Engine Measuring Inlet Manifold Temperature
3500C IMO III Engines Sensor Signal (Analog, Passive) - Test
C18 Generator set and C18 Marine Engines Vibration Damper Guard - Remove and Install
Well Stimulation Pumps Glossary
3500C IMO III Engines Sensor Supply - Test
Well Stimulation Pumps Reference Material