Electric Starting Motor - Remove and Install
Show/hide table
 |
|
Accidental engine starting can cause injury or death to personnel working on the equipment. To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system. Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on. |
- Disconnect the batteries.
- Disconnect the harness assemblies from the electric starting motor.
Show/hide table
Illustration 1 g06319634 - Remove bolts (1).
- Remove the electric starting motor (2).
- Position electric starting motor (2).
- Install bolts (1).
- Connect harness assemblies to the electric starting motor.
- Connect the batteries.
Show/hide table
| |
| Illustration 2 | g06319634 |
Caterpillar Information System:
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Prepare the Machine for Maintenance
C18 Generator set and C18 Marine Engines Coolant Temperature Sensor - Remove and Install
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Product Description
320D3 and 323D3 Excavators Machine System Specifications Final Drive
C18 Generator set and C18 Marine Engines Fuel Pressure Sensor - Remove and Install
320D3 Hydraulic Excavator Engine Supplements Exhaust Elbow - Remove and Install
C18 Generator set and C18 Marine Engines Engine Oil Filter Base - Install - Engine Mounted Oil Filtered Base
C175 Tier 4 Final Engines for Caterpillar Built Machines Fuel and Auxiliary Water Pump Drive - Remove and Install
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankcase Breather - Remove and Install
PM820, PM822, and PM825 Cold Planer Prepare the Machine for Maintenance
797F Tier 4 Off-Highway Truck Engine Supplement Pressure Sensor (Exhaust Inlet) - Remove and Install
New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620} New Brake Software is Now Available For Certain 794 AC and 795F AC Large Off-Highway Trucks {7490, 7610, 7620}
G3500H Generator Set Engine Restriction of Air Inlet and Exhaust
C18 Generator set and C18 Marine Engines Electronic Control Module - Remove and Install
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Crankshaft Rear Seal - Remove and Install
C18 Generator set and C18 Marine Engines Vibration Damper and Pulley - Remove and Install
784C and 785C Off-Highway Truck/Tractors Machine Storage
A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057} A New Procedure for Installing a Radiator Hose Support Is Now Used on Certain 320 GC, 320 and 323 Excavators {1380, 5057}
Software Update is Now Used on Certain 3500 Engines {1920} Software Update is Now Used on Certain 3500 Engines {1920}
Documentation Required for C175 Machine Engines that Experience Unexpected Engine Shutdowns {1000, 7418, 7760} Documentation Required for C175 Machine Engines that Experience Unexpected Engine Shutdowns {1000, 7418, 7760}
3500C IMO III Engines Sensor Signal (Analog, Active) - Test
Aftercoolers May be Missing the Internal Baffle on Certain 3500 Engines {1063, 1063} Aftercoolers May be Missing the Internal Baffle on Certain 3500 Engines {1063, 1063}
G3500H Generator Set Engine Measuring Inlet Manifold Temperature
3500C IMO III Engines Sensor Signal (Analog, Passive) - Test