New Pressure Sensor Group Is Now Used On Certain Cat® Engines with EMCP 4.x Controls {1924, 4490}
- Generator Set
- 3406 GEN SET (S/N: NKM1-UP)
- 3406C GEN SET (S/N: C2G1-UP; C8G1-UP; C2Y1-UP)
- C18 GEN SET (S/N: NKM1-UP)
- 3406C GEN SET (S/N: C2G1-UP; C8G1-UP; C2Y1-UP)
Description Of Change: New engine oil pressure sensor is now used with EMCP 4.x controls on the above mentioned Engines and Gensets.
Adaptable To: A new active 380-1882 Pressure Sensor Gp is now available for use with EMCP 4.x controls.
The new 380-1882 Pressure Sensor Gp is a direct replacement for the former 265-7429 Pressure Sender. Refer to Table 1.
Perform the following steps for product prior to the effective serial numbers:
- Change the harness connector at the sensor to a 297-5484 Connector Plug As with the 5V supply at pin 1, ground at pin 2, and signal at pin 3 using 9X-3402 Connector Socket.
- Add an additional 18 gauge wire to the harness from the new active sensor to the EMCP for a 5V supply from Pin 1 of the sensor connector to Pin 16 on the EMCP4.1 and 4.2 models and from Pin 1 of the sensor connector to pin 56, 61, or 62, Analog input 1, 2, or 3 respectively on the EMCP 4.3 and 4.4 models using a 9X-3402 Connector Socket.
- Change the analog input 1-3 configurable parameter "Signal Type" in the EMCP from "Passive" to "Voltage".
- Change the analog input 1-3 configurable parameter "Signal Range" in the EMCP from "0-5V".
- Set the analog input 1-3 configurable parameter "Maximum Data Range" in the EMCP to "600.000".
Show/hide table
Required Parts | |||
---|---|---|---|
Qty | New Part Number | Description | Former Part Number |
1 | Adapter | - | |
1 | Connector Plug As | - | |
1 | Pressure Sensor Gp | ||
1 | O-Ring Seal | - | |
6 | Connector Socket | - |
Caterpillar Information System:
XQ2000 Power Module Maintenance Interval Schedule
Broken Bolt Survey for all 3500 Engines{1100, 7553} Broken Bolt Survey for all 3500 Engines{1100, 7553}
F Series Excavator Monitoring System WinFlash Menu
2014/09/26 New Improved Advisor Software Is Used on Certain 3600 Engines {1920}
F Series Excavator Monitoring System Device Test Menu
F Series Excavator Monitoring System Calibration Menu
F Series Excavator Monitoring System Override Parameters Menu
F Series Excavator Monitoring System Tool Programming Menu
F Series Excavator Monitoring System Configuration Menu
F Series Excavator Monitoring System Status Menu
F Series Excavator Monitoring System Diagnostic Menu
F Series Excavator Monitoring System ECM Summary Menu
C7.1 Industrial Engine DEF Filler Screen - Clean
C7.1 Marine Engine Inlet Manifold Temperature Sensor
2015/02/02 Improved Pressure Sensor Gp Is Now Used on Certain Cat® Products {1439}
C3.4B Engines DEF Pump Pressure Sensor - Test
XQ125 Generator Set DEF Filler Screen - Clean
TA2 Inspection for C4.4 Industrial Engine{0372, 1000, 7000, 753T, 7565} TA2 Inspection for C4.4 Industrial Engine{0372, 1000, 7000, 753T, 7565}
C4.4 Engines for Caterpillar Built Machines Clean Emissions Module - Remove and Install
C4.4 Engines for Caterpillar Built Machines DEF Injector and Mounting - Remove and Install
C4.4 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Lines - Remove and Install
C4.4 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C4.4 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Tank - Remove and Install
AP500F Asphalt Paver DEF Manifold Filters - Replace