Boom
Show/hide table
Illustration 1 | g03464398 |
Show/hide table
Specification for 432-6350 Two-Piece Boom | |||
Item | Qty | Part | Specification Description |
All bores must be free of paint. Coat all pin bores Including stick, upper frame, bushing, and cylinders with 5P-0960 Grease Cartridge. | |||
1 | 2 | 166-1492 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. |
2 | 2 | 093-1434 Lip Type Seal | |
3 | 2 | 218-5191 Bushing | Make sure that the bushings are installed in the bore so that the identification numbers of the bushings are facing outward.
Bore of the bushing before installation is Installation depth is |
4 | 2 | 8T-4244 Nut | Position nut (5) |
5 | 2 | 8T-4244 Nut | |
As required, use the following shims to adjust the maximum lateral clearance to |
|||
6 | 1 | 133-2717 Shim | Thickness is |
7 | 1 | 093-0064 Shim | Thickness is |
8 | 3 | 093-0065 Shim | Thickness is |
9 | 2 | 093-0097 Shim | Thickness is |
10 | 2 | 099-7091 Shim | Thickness is |
11 | 1 | 093-0086 Shim | Thickness is |
12 | 1 | 093-0118 Shim | Thickness is |
13 | 1 | 7Y-2496 Shim | Thickness is |
14 | 1 | 3B-5317 Cotter Pin | Tighten nut until contact is made with boom. Tighten additional 1/4 turn. Insert cotter pin to lock the castle nut. |
15 | 1 | 296-9586 Pin As | Diameter is |
16 | 1 | 296-9567 Pin | Diameter is |
17 | 2 | 1R-6225 Pin As | Diameter is |
Caterpillar Information System:
Disassembly, Assembly, and Installation of the Oil Heater Pumps and Seals for Certain 3600 and C280 Engines{1333} Disassembly, Assembly, and Installation of the Oil Heater Pumps and Seals for Certain 3600 and C280 Engines{1333}
C12.9 Marine Engines Engine Oil and Filter - Change
C8.7 Marine Engine Engine Oil Level - Check
2013/10/01 New Software is Available for Certain Retrofit Selective Catalytic Reduction Systems (SCR) {1900, 1901, 1920}
C18 Generator Set Refill Capacities
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil Sample - Obtain
2014/12/23 A New Outlet Elbow Is Used on Certain Machine Engines {1307}
2013/10/28 A New Outlet Elbow Is Available for Certain Commercial Engines {1307}
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Sensor Signal (Analog, Passive) - Test
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit CAN Data Link - Test
2013/11/08 New Oil Heater Circulation Pumps and Seal Kits Are Available for Certain 3600 and C280 Engines {1333}
2014/08/01 A New Oil Screen is Used on the High-Pressure Fuel Pump Adapter on C175 Engines {1151, 1162, 1206}
Using the 223-2105 Hose Cutting Machine{0374, 0599, 0678, 0684, 0708, 0738, 5057, 6060} Using the 223-2105 Hose Cutting Machine{0374, 0599, 0678, 0684, 0708, 0738, 5057, 6060}
2014/07/18 A New Outlet Elbow Is Available for Certain Truck Engines {1307}
C12.9 Marine Engines Fuel System Primary Filter/Water Separator - Drain
Crimping XT-3 ES and XT-5 S4G, MCSH, and MCSX Couplings Using 4C-3660, 4C-5052, 4C-5053, 9U-5792, or 9U-7261 Hose Machines{0374, 0599, 0684, 0738, 5057} Crimping XT-3 ES and XT-5 S4G, MCSH, and MCSX Couplings Using 4C-3660, 4C-5052, 4C-5053, 9U-5792, or 9U-7261 Hose Machines{0374, 0599, 0684, 0738, 5057}
C12.9 Marine Engines Fumes Disposal Filter Element - Replace - External
C13 and C15 Generator Sets Single Unit Operation
C8.7 Marine Engine Heat Exchanger - Clean/Test
C9 Generator Set Voltage Regulators
TA2 Inspection for C7.1 Industrial Engine{0372, 1000, 7000, 753T, 7565} TA2 Inspection for C7.1 Industrial Engine{0372, 1000, 7000, 753T, 7565}
C8.7 Marine Engine Model View Illustrations
3600 and C280 Diesel Engine Fluids Recommendations Contamination Control
C8.7 Marine Engine Product Description