Electric Starting Motor - Remove and Install
拆卸步骤
Show/hide table
发动机的意外启动会对在设备上工作的人员造成伤害或死亡。 为避免发动机意外启动,将蓄电池负极(-)端子上的蓄电池电缆拆下。 将所有拆下的蓄电池电缆末端的金属表面用胶布完全粘住,以防止其与其它的金属表面接触而激活发动机的电子系统。 在启动/停止开关的位置上放置“不要操作”的标签,以通知他人该设备正在维修之中。 |
- 将蓄电池断路开关转到断开位置。
- 断开蓄电池。
- 将螺栓 (2) 和垫圈从支架组件 (1) 上拆下。
Show/hide table
图 1 | g03405398 |
- 打开支架组件 (1) 。
- 将电缆组件 (3) 和线束组件 (4) 从电动起动马达 (5) 上断开。
Show/hide table
图 2 | g03405490 |
- 拆下螺栓 (7) 并将接头放到一边。
Show/hide table
图 3 | g03405479 |
- 拆下螺栓 (6) 和托架 (8) 。
- 将适当的起吊设备固定在电起动马达 (5) 上。 拆下将电动起动马达 (5) 固定到飞轮壳的螺栓 (9) 。 拆下电子起动马达 (5) 。 电起动马达 (5) 的重量约为 36 kg (80 lb)。
Show/hide table
图 4 | g03405486 |
- 对其余的电动起动马达重复步骤 5 和 8。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将适当的起吊设备固定在电起动马达 (5) 上。 电起动马达 (5) 的重量约为 36 kg (80 lb)。 将电动起动马达 (5) 安装到飞轮壳上。 安装螺栓 (9) 。
Show/hide table
图 5 | g03405486 |
- 将电缆组件 (3) 和线束组件 (4) 连接到电动起动马达 (5) 上。
Show/hide table
图 6 | g03405490 |
- 拧紧线束组件 (3) 至扭矩为 31 ± 3 N·m (23 ± 2 lb ft)。
- 将线束组件 (4) 拧紧至扭矩为 2.25 ± 0.25 N·m (19.9 ± 2.2 lb in)。
- 对其余的电动起动马达重复步骤 1 和 2。
- 安装支架 (8) 和螺栓 (6) 。
Show/hide table
图 7 | g03405479 |
- 安装螺栓 (7) ,以固定接头。
- 关闭支架组件 (1) 。
Show/hide table
图 8 | g03405398 |
Show/hide table
发动机的意外启动会对在设备上工作的人员造成伤害或死亡。 为避免发动机意外启动,将蓄电池负极(-)端子上的蓄电池电缆拆下。 将所有拆下的蓄电池电缆末端的金属表面用胶布完全粘住,以防止其与其它的金属表面接触而激活发动机的电子系统。 在启动/停止开关的位置上放置“不要操作”的标签,以通知他人该设备正在维修之中。 |
- 将螺栓 (2) 和垫圈安装到支架组件 (1) 上。
- 重新连接蓄电池。
- 将蓄电池断路开关转到接通位置。
Caterpillar Information System:
3516C Petroleum Engines Camshaft - Remove and Install
2013/07/11 A New Band Clamp Is Used on the Exhaust Elbow Groups of Certain 3500C Engines {1061}
2013/07/11 Apply Primer to the Air Cleaner Brackets Prior to Installation on Certain 3512CEngines {1051}
C4.4 Industrial Engine Product Lifting
3516C Petroleum Engines Flywheel - Remove and Install
C7.1 Marine Generator Set Emissions Certification Film
Installation of the 444-6457 Fastener Kit on the Pre-Lubrication Oil Pump Group for Certain G3500 and G3600 Engines{1319, 7553} Installation of the 444-6457 Fastener Kit on the Pre-Lubrication Oil Pump Group for Certain G3500 and G3600 Engines{1319, 7553}
C4.4 Industrial Engine Plate Locations and Film Locations
C7.1 Marine Generator Set Aftercooler Core - Inspect
2013/08/15 A New Water Lines Group Is Used on G3508B Petroleum Engines {1355, 1380, 1393}
2013/11/21 A New Fastener Kit Is Used on the Pre-Lubrication Oil Pump Group of Certain G3500 and G3600 Engines {1319, 7553}
C7.1 Industrial Engine Manifold (Diesel Exhaust Fluid)
C32 Generator Set Product Installation
C175 Generator Set Engines Air Starting Motor - Remove and Install
434-4988 Major Engine Overhaul Foundational Kit for 3406B and 3406C Marine Engines{1000} 434-4988 Major Engine Overhaul Foundational Kit for 3406B and 3406C Marine Engines{1000}
2013/07/25 New Software is Used on Certain 3516C and 3516C HD Generator Set Engines {1920}
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps System Pressure - Release
New Connecting Rod Bolts Are Available for C175 Engines{1218, 7553} New Connecting Rod Bolts Are Available for C175 Engines{1218, 7553}
3500B Marine Propulsion Engines Maintenance Interval Schedule
3516C Petroleum Engines Water Lines
C3.4B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Quality - Test
3516C Marine Engines Thermostatic Valve
C7.1 Industrial Engine Aftertreatment SCR System Dosing - Test
C7.1 Industrial Engine Fuel and the Effect from Cold Weather