Swing Gear and Bearing
Show/hide table
Illustration 1 | g02641256 |
Top view |
Show/hide table
Specification for 333-2879 Swing Gear and Bearing Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
3 | - | - | Position "S" that is on inner race (3) relative to the carbody assembly (1) and bearing stopper (2). Refer to Illustration 1 for correct orientation. |
Show/hide table
Illustration 2 | g02641277 |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
4 | - | - | Before assembly, apply 8C-8422 Sealant between the mating surfaces of the gear group and upper frame assembly. and between the gear group and carbody assembly. |
5 | 8 | 455-3798 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
6 | 4 | 455-3798 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
7 | 1 | 7Y-1095 Dowel | Before assembly, apply Loctite C5A Copper Anti-Seize compound to the dowel holes. |
8 | 54 | 461-3889 Bolt | Before assembly, remove compound, oil and dust from female threads, then apply Loctite C5A Copper Anti-Seize compound to the threads.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 70 ± 5 degrees. |
9 | 1 | 7Y-1650 Hose Clamp | Torque to |
10 | 2 | 457-8759 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
11 | 70 | 461-3887 Bolt | Before assembly, remove compound, oil and dust from female threads, then apply Loctite C5A Copper Anti-Seize compound to the threads.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 55 ± 5 degrees. |
Caterpillar Information System:
C7 Marine Engine Engine Speed/Timing Sensor - Clean/Inspect
C7 Marine Engine Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3508B, 3508C, 3512B, 3512C, 3516B and and 3516C Marine Engines Fluid Recommendations
C7 Marine Engine Refill Capacities
C15 and C18 Petroleum Generator Sets Coolant Extender (ELC) - Add
Procedure for Replacement Grouser Bars {0679, 4172, 4173, 7950} Procedure for Replacement Grouser Bars {0679, 4172, 4173, 7950}
CX31 On-Highway Transmission Transmission Planetary - Assemble
CX31 On-Highway Transmission Transmission Planetary - Disassemble
C7 Marine Engine Coolant (ELC) - Change
C7 Marine Engine Coolant (DEAC) - Change
C7 Marine Engine Product Description
2011/01/06 A New Exhaust Plug Is Used on Certain C18 Engines {1058, 1061}
Equipment and Tools for Undercarriage Rebuilding and Reconditioning Stations {0729, 4150} Equipment and Tools for Undercarriage Rebuilding and Reconditioning Stations {0729, 4150}
336F MHPU Mobile Hydraulic Power Unit Machine System Specifications Air Cleaner - Mounting
Procedures to Salvage Thrust Faces on Planetary Carriers {3160, 4050, 4051, 4093} Procedures to Salvage Thrust Faces on Planetary Carriers {3160, 4050, 4051, 4093}
A New Aftercooler Is Used on Certain C9 Marine Engines {1063} A New Aftercooler Is Used on Certain C9 Marine Engines {1063}
Troubleshooting the Hydraulic Electronic Unit Injection (HEUI) Fuel System On C7 and C9 Engines{1250} Troubleshooting the Hydraulic Electronic Unit Injection (HEUI) Fuel System On C7 and C9 Engines{1250}
C7 Marine Engine Injector Bolt Torque - Inspect
3508C, 3512C and 3516C Locomotive Engines Engine Oil Lines
Replacing the Fuel Injection Pump on Certain C9.3 Engines {1251, 1290} Replacing the Fuel Injection Pump on Certain C9.3 Engines {1251, 1290}
3516C Locomotive Engines Flywheel Housing - Remove
CX31 On-Highway Transmission Retarder - Remove
3516C Locomotive Engines Flywheel Housing - Install
CX31 On-Highway Transmission Retarder - Install