Rear Axle Oil Cooler - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-9202     | 杠杆式拉拔举倾机构总成     | 1     |
B     | 189-0408     | 钩环组件     | 2     |
Show/hide table
车斗降下后,车斗与机架之间没有空隙。 如果不安装固定缆线,可能会导致在此区域作业的人员受伤或死亡。 |
Show/hide table
在工作温度下,液压油箱是热的,而且有压力。 热油和热的部件可能会导致人身伤害。 不要让热油或热的部件与皮肤接触。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才可卸下加注口盖。 慢慢取下加注口盖,让压力释放掉。 |
- 如果配备有抑噪配置,则请参阅专门说明书, " 351-3820 抑噪配置(如有配备)的安装",了解专用面板位置和正确的拆卸或安装步骤。
- 安装车斗固定拉线。 操作和保养手册, "拉线(车斗固定)"。
- 释放系统压力。 请参阅操作和保养手册, "系统压力释放"。
- 将后桥机油冷却器排入适当的容器,以供保存或处理。
- 断开软管组件 (1) 、软管组件 (2) 和线束组件 (3) 。 拆下接线紧固件。
Show/hide table
图 1 | g02065054 |
- 断开软管组件 (4) 、软管组件 (5) 和线束组件 (6) 。 拆下接线紧固件。
Show/hide table
图 2 | g02160651 |
- 断开软管组件 (7) 和软管组件 (8) 。
Show/hide table
图 3 | g02160655 |
- 将工具 (A) 、工具 (B) 和适当的起吊设备连接到机油冷却器 (9) 上。 机油冷却器 (9) 的重量约为 295 kg (650 lb)。
Show/hide table
图 4 | g02160658 |
Show/hide table
图 5 | g02160665 |
- 拆下螺栓 (10) 。 拆下机油冷却器 (9) 。
安装步骤
- 按相反顺序安装油冷却器 (9) 。
- 检查机油油位。 参考操作和保养手册, "加注容量"。
Caterpillar Information System:
C175 Generator Sets Coolant (DEAC) - Change
C175 Generator Sets Control Panel - Inspect/Test
Reassembly of the Throttle Body for Certain G3516B Engines{1265} Reassembly of the Throttle Body for Certain G3516B Engines{1265}
C175 Generator Sets Battery - Replace
C27 and C32 Tier 4 Engines Data Link - Test
325 VM and VH Variable Gauge Undercarriage Recoil Spring - Assemble
325 VM and VH Variable Gauge Undercarriage Recoil Spring - Disassemble
3512C SR4B Generator Sets Model View Illustrations
C27 and C32 Tier 4 Engines Electrical Power Supply - Test
C15 and C18 Industrial Engines Water Temperature Regulator Housing - Remove and Install
12M, 140M and 160M Motor Graders Hydraulic and Steering System Blade Lift Cylinder
C27 and C32 Tier 4 Engines Sensor Signal (PWM) - Test
C18 Marine Generator Set Overhaul (Top End)
C18 Marine Generator Set Overhaul (Major)
C175 Generator Sets Coolant (ELC) - Change
C175 Generator Sets Coolant Extender (ELC) - Add
C175 Generator Sets Coolant Level - Check
C175 Generator Sets Coolant Sample (Level 1) - Obtain
C175 Generator Sets Coolant Sample (Level 2) - Obtain
C175 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
C175 Generator Sets Engine Valve Lash - Check
C175 Generator Sets Space Heater - Test
C15 and C18 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225} Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}