Cylinder Head
Show/hide table
| |
| Illustration 1 | g02823679 |
Show/hide table
| Specification for 350-5204 Cylinder Head Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 2 | 130-2607 Valve Seat Insert | During installation, shrunk the valve seat insert with reduced temperature (reference temperature : |
| 2 | 2 | 130-2608 Valve Seat Insert | During installation, shrunk the valve seat insert with reduced temperature (reference temperature : |
| 3 | 5 | 3B-0623 Cup Plug | Apply Loctite 11358 to the bores for the cup plugs prior to the installation. |
| 4 | 5 | 3B-0645 Cup Plug | Apply Loctite 11358 to the bores for the cup plugs prior to the installation. |
| D | - | - | Installation depth for cup plug is |
| E | - | - | Installation depth for cup plug is |
Show/hide table
| |
| Illustration 2 | g02823696 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 5 | 1 | 5B-7890 Pipe Plug | Before assembly, lubricate the threads with Loctite C5A Copper Anti-Seize. |
| 6 | 6 | 131-0420 Cylinder Head Fastener Gp | Use the following procedure to tighten the bolts for the cylinder head:
1. Before assembly, apply clean engine oil to the threads of the bolts. 2. Tighten bolt 1 through bolt 8 in the numerical sequence as shown in Illustration 2 to a torque of 3. Again, tighten bolt 1 through bolt 8 in the numerical sequence as shown in Illustration 2 to a torque of 4. Again, retighten bolt 1 through bolt 8 in the numerical sequence as shown in Illustration 2 to a torque of 5. Loosen bolt 1 through bolt 8 in the numerical sequence to an angle of 90 ± 5 degrees as shown in Illustration 2 . 6. Again, retighten bolt 1 through bolt 8 in the numerical sequence as shown in Illustration 2 to a torque of 7. Tighten two bolts (8) only after bolt 1 through bolt 8 have been given the final torque. 8. Tighten two bolts (8) to |
| 7 | 2 | 131-0421 Cylinder Head Fastener Gp | |
| 8 | 2 | 5B-0213 Bolt |
Caterpillar Information System:
C6.6 Generator Set Data Link Circuit - Test
Roller Servicing Equipment, Tooling, Literature, and Training Review {0374, 4154, 4180, 4181, 7561} Roller Servicing Equipment, Tooling, Literature, and Training Review {0374, 4154, 4180, 4181, 7561}
3508, 3512 and 3516 Generator Set Engines Tachometer Drive - Remove and Install
2010/02/19 A New Fuel Transfer Pump and a New Check Valve Are Now Used on Certain C32 Marine Engines {1256, 1262}
C6.6 Generator Set Fuel Rail Pump Solenoid - Test
C6.6 Generator Set CAN Data Link Circuit - Test
C6.6 Generator Set CID 1779 FMI 08
2010/01/08 Correct Usage of Seals and Spacers on the Valve Mechanism Covers of Some C9 Engines {1107, 7555}
C6.6 Generator Set CID 1690 FMI 08
3512C HD Locomotive Engine Product Lifting
C6.6 Generator Set CID 2246 FMI 06
C6.6 Generator Set CID 1797 FMI 04
C6.6 Generator Set Ignition Keyswitch Circuit and Battery Supply Circuit - Test
793F Off-Highway Truck Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
CEM Locomotive Aftertreatment Catalyst (DOC) - Clean/Inspect
3516C Generator Sets Catalyst (DOC) - Replace
Selecting Connectors and Preparing Cables for Wiring an Uninterruptible Power Supply{4480} Selecting Connectors and Preparing Cables for Wiring an Uninterruptible Power Supply{4480}
C13, C15, and C18 Tier 4 Interim Engines Ether Starting Aid - Test
C27 and C32 Engines for Caterpillar Built Machines Cooling System - Test
C27 and C32 Engines for Caterpillar Built Machines Electronic Unit Injector - Adjust
793F Off-Highway Truck Machine Systems Hoist Electronic Control - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Engine Crankcase Pressure (Blowby) - Test
Bench Test Procedure For A CX35 On-Highway Transmission and a CX35-P800 Petroleum Transmission {3030, 3073} Bench Test Procedure For A CX35 On-Highway Transmission and a CX35-P800 Petroleum Transmission {3030, 3073}
3512E HD Petroleum Engine Product Description