Final Drive Planetary Carrier (In Chassis) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Bolts M16 x 1.5 by 10 in Long | 2 |
B | 439-3940 | Link Bracket | 1 |
C | 439-3938 | Link Bracket | 1 |
Start By:
- Remove the axle.
Note: Position the final drive drain plug on the bottom of the final drive. Remove the drain plug.
- Drain the oil from the final drive. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change".
Show/hide table
Illustration 1 g06362043 - Remove two bolts (1) and install Tooling (A). Remove the remaining bolts (1).
Show/hide table
Illustration 2 g06362064 - Attach Tooling (B) to outer planet carrier (2). Attach a suitable lifting device to Tooling (B). The weight of outer planet carrier (2) is approximately
109 kg (240 lb) . - Use a suitable pry bar to separate the outer planet carrier (2) from the housing. Remove outer planet carrier (2).
Show/hide table
Illustration 3 g06362284 - Remove O-ring seal (3) from outer planet carrier (2).
Show/hide table
Illustration 4 g06362292 - Remove thrust ring (4) from inner planet carrier (5).
Show/hide table
Illustration 5 g06362294 - Attach Tooling (C) to inner planet carrier (5). Attach a suitable lifting device to Tooling (C). The weight of inner planet carrier (5) is approximately
68 kg (150 lb) . Remove inner planet carrier (5).Show/hide tableIllustration 6 g06362297 - Remove thrust ring (6) and lip seal (7).
- Install outer planetary carrier (2) and inner planetary carrier (5) in the reverse order of removal.
- Install lip seal (7) in the direction indicated in Illustration 7 towards the center of the machine.
- Tighten bolts (1) to a torque of
270 ± 40 N·m (199 ± 30 lb ft) .
Show/hide tableIllustration 7 g06362316
Caterpillar Information System:
C9.3B Engines Cylinder Head
3512E Oil Well Service Engine Fuel System Primary Filter/Water Separator - Drain
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Fuel System Primary Filter (Water Separator) - Drain
3512E Oil Well Service Engine Fuel System Secondary Filter - Replace
Rework Procedure for Weld Crack on A-Pin Doubler Plate for Certain 966L, 966M, 972L, and 972M Medium Wheel Loaders {0679, 7054} Rework Procedure for Weld Crack on A-Pin Doubler Plate for Certain 966L, 966M, 972L, and 972M Medium Wheel Loaders {0679, 7054}
C9.3B Engines Speed/Timing Sensor
C9.3B Engines Cylinder Head Valves
D9T Track-Type Tractor Systems Bevel and Transfer Gears
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Diesel Particulate Filter - Clean/Replace
3512E Oil Well Service Engine Engine Air Cleaner Element (Dual Element) - Replace
988K XE Wheel Loader STIC Control (Steering Deadband) - Adjust
Side/Snow Counterweight Mounting Plate Assembly May Fail on Certain 910K and 914K Compact Wheel Loaders {7056} Side/Snow Counterweight Mounting Plate Assembly May Fail on Certain 910K and 914K Compact Wheel Loaders {7056}
3512E Oil Well Service Engine Engine Air Precleaner - Check/Clean
3512E Oil Well Service Engine Engine Oil Level - Check
3512E Oil Well Service Engine Engine Oil and Filter - Change
Shop Repair Procedure for D6 and D7 Size Track with Positive Pin Retention 2 {4169, 4170, 4171, 4174, 4175, 4180} Shop Repair Procedure for D6 and D7 Size Track with Positive Pin Retention 2 {4169, 4170, 4171, 4174, 4175, 4180}
D8T and D9T Track-Type Tractors Torque Converter
C9.3B Engines Engine Oil Lines
D8T and D9T Track-Type Tractors Machine Movement
New Final Drive and Brake (Wheel) Group Now Used on AD45B Underground Articulated Trucks {4011} New Final Drive and Brake (Wheel) Group Now Used on AD45B Underground Articulated Trucks {4011}
C9.3B Engines Gear Group (Front)
C9.3B Engines Cylinder Block Cover Group
C9.3B Engines Electronic Unit Injector Wiring
C9.3B Engines Cylinder Liner