Housing (Front) - Remove
Start By:
- Remove the expansion tank. Refer to Disassembly and Assembly, "Expansion Tank - Remove ".
- Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
- Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
- Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove".
- Remove the front engine support. Refer to Disassembly and Assembly, "Engine Trunnion - Remove and Install".
- Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove covers (1).
- Remove bracket (2).
- Reposition fuel filter assembly (3).
- Remove bolts (4) and remove bracket (5).
Show/hide table
Illustration 2 g01147758 - Remove bolts (6) and dampers (7). Disconnect the harness assembly behind damper (7).
Show/hide table
Illustration 3 g01188104 - Loosen flanges (8).
Show/hide table
Illustration 4 g01367057 - Remove adapters (9).
- Attach a suitable lifting device to front housing (10). The weight of front housing (10) is approximately
67 kg (148 lb) . - Remove bolts (11) and bolts (12).
- Remove front housing (10) and the gasket.
Show/hide table
| |
| Illustration 1 | g01367056 |
Caterpillar Information System:
C18 Marine Auxiliary Engines Indicator Lamp - Test
TA19 and TA22 Transmissions Power Train Electronic Control System Event Code List
C18 Marine Auxiliary Engines Switch Circuits - Test
2007/04/09 An Improved Clamp is Used {1355, 1380, 1393}
C9 Agricultural Engine for Challenger Tractors Engine Misfires, Runs Rough or Is Unstable
C32 Marine and Auxiliary Marine Engines Vibration Damper and Pulley - Remove and Install
2009/02/02 A New Pushrod Is Now Used {1102, 1121, 1123}
3512B Marine Auxiliary Engine Overhaul (Top End)
2007/04/02 Make Sure That The Turbocharger Coolant Is Vented {1052}
C9 Agricultural Engine for Challenger Tractors Sensor Supply - Test
C18 Generator set and C18 Marine Engines Valve Mechanism Cover Base - Remove and Install
C9 Agricultural Engine for Challenger Tractors Acceleration Is Poor or Throttle Response Is Poor
3512B Marine Auxiliary Engine Safety Messages
Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064} Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064}
C32 Petroleum Engines Belts - Inspect/Adjust/Replace
C32 Marine Engines Housing (Front) - Install
C18 Marine Auxiliary Engines Engine Top Speed Is Not Obtained
C15 and C18 Petrolem Generator Set Engines General Information
C18 Marine Auxiliary Engines Diagnostic Code Cross Reference
584 and 584HD Forwarders Visibility Information
CX28 On-Highway Transmission Transmission Planetary - Disassemble
CX28 On-Highway Transmission Transmission Planetary - Assemble
C32 Marine and Auxiliary Marine Engines Crankshaft Main Bearings - Remove
C32 Marine Propulsion Engines Component Location