Governor and Fuel Transfer Pump - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 6V-0006     | Connector Pliers     | 1     |
B     | 128-8827     | Pin (1)     | 1     |
C     | 1U-7523     | Pin Pilot (1)     | 1     |
Show/hide table
( 1 ) | Part of 9U-7305 Tool Group |
- Install the O-ring seal on governor (17). Carefully install governor (17) so that the fuel control linkage is not damaged. Install the washers and bolts (16) .
Show/hide table
Illustration 1 | g00344799 |
- Install Tooling (B) into link pin (15) of the governor output shaft. When Tooling (B) is properly installed, equal lengths of the smaller end of Tooling (B) will extend from both ends of link pin (15) .
Show/hide table
Illustration 2 | g00344797 |
Show/hide table
Illustration 3 | g00344798 |
- Install Tooling (C) onto the smaller end of Tooling (B) in order to help to align link pin (15) .
- Use Tooling (A) to slide sleeve (14) away from the cylinder head and toward the governor. Install clip (13) .
- Install cover (12) .
Show/hide table
Illustration 4 | g00344796 |
- Put hose assembly (10) in position. Install clip (11), the washer and the bolt.
- Connect tube assemblies (7), (8) and (9) .
Show/hide table
Illustration 5 | g00344795 |
- Put bracket (5) and throttle cable (4) in position. Install bolts (6) and the nuts.
Show/hide table
Illustration 6 | g00344794 |
- Connect throttle cable (4) .
- Connect three wires (3) .
Show/hide table
Illustration 7 | g00344792 |
- Install new tie-wrap (2) .
- Connect hose assembly (1) .
- Check the fuel setting adjustment.
Reference: Refer to Systems Operation/Testing and Adjusting, SENR3583, "Basic Engine Components for 3114, 3116 and 3126 Engines" for the proper procedure.
- Turn the battery disconnect switch to the OFF position and remove the key.
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
966F Series II Wheel Loader Power Train Transmission Hydraulic Control Operation
627G Wheel Tractor-Scraper Wheel Scraper Power Train Performance Checks
627G Wheel Tractor-Scraper Wheel Scraper Power Train Operational Checks
966F Wheel Loader and 966F Series II Wheel Loader Hydraulic System Implement Cycle Time - Check
621G and 623G Wheel Tractor-Scrapers Wheel Tractor Power Train Retarder
623G Wheel Tractor-Scraper Hydraulic System Relief Valve (Main) - Test and Adjust
2001/12/24 New Water Valve Assembly and Board Control Assembly Improve Reliability of the HVAC System {7320}
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 1610 - FMI 05
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 1608 - FMI 05
950F Wheel Loader and 950F Series II Wheel Loader Air System and Brakes Parking Brake for Models with Hydraulic Brakes
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 1607 - FMI 05
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 1606 - FMI 05
Caterpillar Monitoring System Temperature Sender
994D Wheel Loader Power Train Machine Preparation for Troubleshooting
2000/09/18 Additional Information Is Available on the Brake Lines of Wheel Loaders {4257, 4269}
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Radiator and Fan - Install
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H and 16H Motor Graders Caterpillar Monitoring System Fuel Level Sender
950F Wheel Loader and 950F Series II Wheel Loader Air System and Brakes Brake Control Valve (Parking) for Air Over Hydraulic Brakes
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0042 FMI 11 Inject Actuation Control Valve open/short
966G II and 972G II Wheel Loaders Machine Configuration
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electrical Power Supply
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0094 FMI 03 Fuel Pressure open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0094 FMI 04 Fuel Pressure short to ground
Caterpillar Monitoring System Harness Code