Exhaust Manifold - Remove and Install
拆卸步骤
开始:
- 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。
- 按相反的数字顺序拆下调整螺钉 (1) 。 请参阅插图 1。 这将有助于防止排气歧管变形。
Show/hide table
 | |
| 图 1 | g00951398 |
- 从缸盖上拆下排气歧管，然后拆下排气歧管密封垫。 废弃排气歧管密封垫。
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | - | 导向螺栓 (M10 X 1.5 X 100 mm) |
2 |
注: 排气歧管安装不当可能会造成排气歧管开裂。 必须按照正确的顺序，将固定排气歧管的调整螺钉拧紧到正确的扭矩。
- 将工具 (A) 安装到缸盖的孔 (X) 中。
Show/hide table
 | |
| 图 2 | g00951297 |
- 将一个新的排气歧管密封垫定位到缸盖中的工具 (A) 上。 将排气歧管定位到工具 (A) 上。 用手安装调整螺钉 (1) ，将排气歧管固定到缸盖上。
注: 切勿在排气歧管密封垫上涂抹任何密封胶。
- 拆下工具 (A) 。 安装其余的调整螺钉 (1) ，然后将调整螺钉均匀拧紧至 33 N·m (24 lb ft) 的扭矩。 按照图 2 中所示的顺序拧紧调整螺钉。
End By: 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
C11 and C13 Industrial Engines Cylinder Block
C-15 Petroleum Engine Auxiliary Water Pump - Remove
C13 Engine for Combat and Tactical Vehicles Engine Oil Pan
C11 and C13 Petroleum Engines Engine Oil Pan
C11 and C13 Industrial Engines Engine Oil Pan
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Engine Vibration Troubleshooting
3054E Industrial Engine Valve Mechanism Cover - Remove and Install
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Fuel System - Prime
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Fuel Injection Timing - Check
C1.5 and C2.2 Generator Sets Additional Messages
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Electrical System
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Basic Engine
C1.5 and C2.2 Generator Sets Engine Crankcase Breather - Clean/Replace
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Clutch Pedal Position Switch Circuit - Test
C-15 Petroleum Engine Auxiliary Water Pump - Install
C7 and C9 On-Highway Engines 0168-00 Excessive ECM Battery Power (17)
3054E Industrial Engine Cylinder Head - Remove
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Serial Number Plate
C1.5 and C2.2 Generator Sets Generator Set Installation
C15 and C18 Petroleum Generator Sets Engine - Clean
G3520B Engines Jacket Water to Engine Oil Differential Temperature (Low)
3054E Industrial Engine Cylinder Head - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Cruise Control Switch Circuit - Test
Additional Information for the Customer Communication Module (CCM) that Is Used on Series 3500 and Series 3600 Gas Applications{1926} Additional Information for the Customer Communication Module (CCM) that Is Used on Series 3500 and Series 3600 Gas Applications{1926}