Pilot Lines
Show/hide table
| |
| Illustration 1 | g03155477 |
|
Top view | |
Show/hide table
| |
| Illustration 2 | g03155478 |
|
View A-A | |
Show/hide table
| Specification for 325-8954 Pilot Lines Gp | |||
| Item | Qty | Part | Specification Description |
| - | 7 | 7K-1181 Cable Strap | Sharp corners at the cutting edge of each cable strap shall not be allowed. |
| 1 | 3 | 148-8378 Elbow As | Torque to |
| 2 | 2 | 168-1968 Tee As | Torque to |
| 3 | 2 | 338-6970 Pressure Sensor Gp | Out put type is PWM.
Out put frequency is 500 Hz Before assembly, apply a thin layer of hydraulic oil to out side diameter of male thread. Use tightening tool with 6 PT or 12 PT 1-1/16 inch deep socket. Torque to |
Show/hide table
| |
| Illustration 3 | g03155476 |
|
View B-B | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 4 | 1 | 164-6874 Elbow Fitting | Torque to |
| 5 | 1 | 148-8443 Tee | Torque to |
Show/hide table
| |
| Illustration 4 | g03155536 |
|
View C-C With lift mode | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 6 | 1 | 148-8378 Elbow As | In case of aluminum manifold tighten to |
Show/hide table
| |
| Illustration 5 | g03155537 |
|
View C-C Without lift mode | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 7 | - | - | In case of aluminum manifold tighten fitting to |
Caterpillar Information System:
336E Excavator Machine System Specifications Pilot Lines
336E Excavator Machine System Specifications Front Lines
Installation of the Generator and Control Panel Components for Dynamic Gas Blending Retrofits on Certain 3500 Engines{4490, 7451} Installation of the Generator and Control Panel Components for Dynamic Gas Blending Retrofits on Certain 3500 Engines{4490, 7451}
312F, 313F, 316F and 318F Excavators Wiring Harness (Short Circuit) - Test
336E Excavator Machine System Specifications Pilot Lines
Procedure to Install the 380-3967 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057, 5362, 6547} Procedure to Install the 380-3967 Connecting Lines Gp (Thumb) on Certain Hydraulic Excavators{5057, 5362, 6547}
312D2 and 313D2 Excavators Hydraulic System Electronic Control System
312D2 and 313D2 Excavators Specifications
312D2 and 313D2 Excavators Hydraulic System Boom Hydraulic System
312D2 and 313D2 Excavators Hydraulic System Main Hydraulic System
311B and 312B Excavators Hydraulic System Swing Bearing Movement - Measure
307C Excavator Hydraulic System Swing Bearing Movement - Measure
336E Excavator Machine System Specifications Pilot Lines
336E Excavator Machine System Specifications Pilot Lines
336F and 340F Excavators Machine System Boom System
318E Excavator C4.4 Engine Supplement Fuel Manifold - Remove and Install
318E Excavator C4.4 Engine Supplement Diesel Particulate Filter - Remove and Install
318E Excavator C4.4 Engine Supplement Soot Antenna - Remove and Install
318E Excavator C4.4 Engine Supplement Soot Sensor - Remove and Install
318E Excavator C4.4 Engine Supplement Temperature Sensor (DPF) - Remove and Install
336E Excavator Machine System Specifications Front Lines
336E Excavator Machine System Specifications Front Lines
Flywheel Housing Salvage for Excavator C18 Engines {0677, 1157} Flywheel Housing Salvage for Excavator C18 Engines {0677, 1157}
318E Excavator C4.4 Engine Supplement Pressure Sensor (DPF) - Remove and Install - Clean Emissions Module