Crankshaft Rear Seal - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 9S-8871     | 密封件定位器     | 1     |
9S-8890 | 螺栓     | 3     | |
6V-7876 | 安装工具     | 1     |
|
9S-8858 | 安装工具螺母     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 按照以下步骤,使用工具 (A) 安装曲轴后油封 (6) 和承磨衬套 (1) :
- 使用 4C-9500 快速固化底漆 来清洁曲轴 (3) 外周以及承磨衬套 (1) 的内周。
- 将承磨衬套 (1) 和油封 (6) 安装到曲轴 (3) 上。 将 6V-7876 油封安装工具 (4) 放置在 9S-8871 密封件定位器 (2) 上。 润滑 9S-8858 安装工具螺母 (5) 和垫圈的表面。 将 9S-8858 安装工具螺母 (5) 和垫圈安装在 9S-8871 密封件定位器 (2) 上。
- 拆下工具 (A) ,然后检查曲轴油封和承磨衬套是否安装正确。
注: 一旦密封圈与承磨衬套分开,不得再次使用这些部件。 进行有关密封件维修前,请参考专门说明书, SMHS8508。
注: 在安装曲轴油封和承磨衬套的过程中,不要使用任何类型的润滑剂。
注: 在安装承磨衬套前,检查曲轴有无划伤,或者曲轴表面有无任何可能导致失圆状态的变形。 使用抛光布清除曲轴上的瑕疵。
Show/hide table
图 1 | g00517174 |
End By: 安装飞轮。 请参考 解体与组装, "飞轮 - 安装"。
Caterpillar Information System:
3306B Industrial Engine Crankshaft Front Seal - Install
3600 Heavy Fuel Engines Sensors and Electrical Components
3408C, 3412C and 3412D High Performance Marine Engines Engine Oil Filter Base
3306C Engines for Caterpillar Built Machines Water Pump
3306B Industrial Engine Shutoff And Alarm System Components
3306B Industrial Engine Fan Drive - Install
3306B Industrial Engine Instruments and Indicators
3406E On-Highway Engine Camshaft - Install
3306B Industrial Engine Time Delay Relay
3306B Industrial Engine Electric Shutoff System
3306B Industrial Engine Rear Power Take-Off (RPTO)
3306B Industrial Engine Shutoff and Alarm System
3306C Engines for Caterpillar Built Machines Valve Rocker Arms and Lifters
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pump
3406E On-Highway Engine Camshaft Bearings - Remove
3600 Heavy Fuel Engines Magnetic Pickups - Clean/Inspect
3306B Industrial Engine Gauges and Indicators
3406C Engines for Caterpillar Built Machines Water Pump
3306B Industrial Engine Cold Weather Starting
G3300 Engines Ignition Systems
3408B and 3408C Industrial and Marine Engines Gear Group (Rear)
G3300 Engines Product Description
3306B Industrial Engine Cylinder Head - Install
3306B Industrial Engine Power Take-Off Clutch