3126B Truck Engine Caterpillar


Customer Specified Parameters

Usage:

3126 6PZ
To record programmed specifications, use the following blanks.

Customer Passwords

  • First Password ____________________

  • Second Password ____________________

Power Rating (hp at rpm) ____________________

Rating Selection (A-E) ____________________

Vehicle ID ____________________

Vehicle Speed Parameters

  • Vehicle Speed Calibration ____________________ pulses per km (pulses per mile)

  • Vehicle Speed Limit ____________________ km/h (mph)

  • Vehicle Speed Limit Protection ____________________

  • Tachometer Calibration ____________________ pulses per revolution

  • Soft Vehicle Speed Limit ____________________

Cruise Control Parameters

  • Low Cruise Control Speed Set Limit ____________________ km/h (mph)

  • High Cruise Control Speed Set Limit ____________________ km/h (mph)

  • Engine Brake ____________________

  • Cruise/Idle/PTO Switch Configuration ____________________

  • Soft Cruise Control ____________________

Idle Parameters

  • Idle Vehicle Speed Limit ____________________ km/h (mph)

  • Idle RPM Limit ____________________

  • PTO Engine Speed Ramp Rate ____________________ rpm/sec

  • PTO Bump RPM ____________________

PTO Parameters

  • PTO Configuration ____________________

  • PTO Top Engine Limit ____________________

  • PTO Engine RPM Set Speed ____________________

  • PTO to Set Speed ____________________

  • PTO Cab Throttle RPM Limit ____________________

  • PTO Vehicle Speed Limit ____________________

  • Torque Limit ____________________ N·m (lb ft)

  • PTO Shutdown Time ____________________

  • PTO Activation of Cooling Fan (If Equipped) ____________________

Engine/Gear Parameters

  • Lower Gears Engine RPM Limit ____________________

  • Lower Gears Turn Off Speed ____________________ km/h (mph)

  • Intermediate Gears Engine RPM Limit ____________________

  • Intermediate Gears Turn Off Speed ____________________ km/h (mph)

  • Gear Down Protection RPM Limit ____________________

  • Gear Down Protection Turn On Speed ____________________ km/h (mph)

  • Top Engine Limit ____________________

  • Low Idle Engine RPM ____________________

  • Transmission Style (If Equipped) ____________________

Timer Parameters

  • Idle Shutdown Time ____________________

  • Idle Shutdown Override Allowance ____________________

  • A/C Pressure Switch Fan On - Time (If Equipped) ____________________

  • Fan with Engine Brake On - Full (If Equipped) ____________________

Engine Monitoring Mode

  • "OFF" ____________________

  • "Warning" ____________________

  • "Warning/Derate" ____________________

  • "Warning/Derate/Shutdown" ____________________

  • "Coolant Level Sensor Enable/Disable" (If Equipped) ____________________

Maintenance Indicator Parameters

  • Manual-Hours

  • Auto-Hours

  • Manual-Fuel

  • Auto-Fuel

Dash Display Access Parameters

  • Adjust Customer Parameters ____________________

  • PM1 Reset ____________________

  • Theft Deterrent System Control ____________________

  • Theft Deterrent Password ____________________

Output Parameters

  • Fan Control Type (If Equipped) ____________________

Data Link Parameters

  • Powertrain Data Link ____________________

Caterpillar Information System:

Installation And Commissioning Procedures For The 3600 Marine Monitoring System{1901} Installation And Commissioning Procedures For The 3600 Marine Monitoring System{1901}
C-10 and C-12 Truck Engines Glossary of Electronic Control Terms
3406E and 3456 Industrial Engines Battery or Battery Cable - Disconnect
C-10 and C-12 Truck Engines General Information
SPP101 Skid Mounted Pumper Belts - Inspect/Adjust/Replace
C-10 and C-12 Truck Engines Engine Design
C-10 and C-12 Truck Engines Engine Design
3126 Truck Engine (Military) Starting the Engine
G3612 and G3616 Engines Electrohydraulic System Oil - Change
Electronic Modular Control Panel II+ (EMCP II+) AL Fault Codes
G3612 and G3616 Engines Electrohydraulic System - Inspect
G3612 and G3616 Engines Electrohydraulic System - Check/Adjust
3126E and 3126B Commercial and Truck Engines Emissions Certification Film
3126E Truck Engines Engine Operation
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Camshaft
C-10 and C-12 Truck Engines Electronic Control System Components
3406E and 3456 Engines for Caterpillar Built Machines Fuel System
318B Excavator Machine System Specifications Front Idler
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Connecting Rod
3126 Truck Engine Engine Design
3512 Industrial Engine Model View Illustrations
3306B Industrial Engine Air Tank Moisture and Sediment - Drain - If Equipped
3512B Engine and SPF343, SPS343 and SPT343 Pumpers Crankcase Pressure Sensor
3126 Industrial Engine Fuel Lines
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.