General Information (Calibration)
Payload Calibration Introduction
Your Cat® Dealer will calibrate your Cat Production Measurement application.
Calibration provides necessary information for the application. Calibration allows this application to determine the weight of the material that is lifted by the wheel loader. During calibration, the application measures the following:
- Lift cylinder pressure
- Lift position
- Linkage speed
- Tilt position
- Hydraulic oil temperature
There are two tools that can be used to perform a calibration:
- The Display Module
- Cat® Electronic Technician (Cat ET) Service Tool
Calibration using both tools is covered in the following text.
The types of calibrations are:
- Simple Calibration Update
- System Calibration Using Display Module
- System Calibration Using Cat ET Service Tool
All types are covered in this manual.
Caterpillar Information System:
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Troubleshooting
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager VIMSpc Payload Reports
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager VIMSpc Software
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Service Tool Software
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Weigh Range Adjusting
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Service Menu
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Totals Menu
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Reweigh Operation
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Zero Operation
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Normal Weighing Operation
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Payload Menu
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Menu Navigation
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Calibration Using Display Module
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Calibration Using Electronic Service Tool
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager System Schematic
793D Off-Highway Truck Power Train Drive Shaft (Main)
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Lift and Tilt Cylinder Speed - Check
980L Tier 3 Wheel Loader Machine System Loader Frame to Rear Frame - Connect
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Transmission Oil Filter - Replace
416F2, 420F2 and 430F2 Backhoe Loaders Engine Air Filter Primary Element - Clean/Replace
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Air Cleaner Dust Valve - Clean/Inspect
990K Wheel Loader Systems Steering Control Group
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Engine Supplement Water Separator and Fuel Filter (Primary) - Remove and Install
Felling Head Limiter Crack Repair Procedure {6712} Felling Head Limiter Crack Repair Procedure {6712}