Transmission Oil Filter - Replace
Show/hide table
 |
|
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
a. Prepare the machine for maintenance. Refer to Operation and Maintenance Manual, "Prepare the Machine for Maintenance".
- Remove the drain plugs from the end cap, and store the plugs for reuse.
- Drain the oil into a suitable container, and recycle the oil.
Show/hide table
| |
| Illustration 1 | g06131916 |
- Discard the seals for the drain plugs.
- Clean the drain plugs in a clean, nonflammable solvent.
- Install new seals on the drain plugs.
Show/hide table
| |
| Illustration 2 | g06131919 |
- Install the drain plugs, and tighten the plugs to the proper torque.
Show/hide table
| |
| Illustration 3 | g06131920 |
- Remove the bolts for the end cap, and store the bolts for reuse.
- Remove the end cap from the filter housing, and store the end cap for reuse.
Show/hide table
| |
| Illustration 4 | g06131922 |
- Remove the filter elements, and properly discard the elements.
Show/hide table
| |
| Illustration 5 | g06131926 |
- Discard the seal for the end cap.
- Clean the end cap in a clean, nonflammable solvent.
- Install a new seal on the end cap.
Show/hide table
| |
| Illustration 6 | g06131927 |
- Install the new filter elements and the end cap.
- Install the bolts for the end cap, and tighten the bolts to the proper torque.
Show/hide table
| |
| Illustration 7 | g06131930 |
- Start the engine, and operate the engine at low idle for 5 minutes.
- Check for leaks, and make any necessary repairs.
Show/hide table
| |
| Illustration 8 | g06131932 |
- Check the oil level in the torque converter sump and, if necessary, add oil. For the proper procedure, refer to Operation and Maintenance Manual, "Torque Converter Sump Oil Level - Check".
Show/hide table
| |
| Illustration 9 | g06152974 |
Note: The oil level in the transmission is supplied by the torque converter sump.
Caterpillar Information System:
980L Tier 3 Wheel Loader Machine System Loader Frame to Rear Frame - Connect
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Lift and Tilt Cylinder Speed - Check
793D Off-Highway Truck Power Train Drive Shaft (Main)
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager System Schematic
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Calibration Using Electronic Service Tool
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Calibration Using Display Module
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager General Information (Calibration)
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Troubleshooting
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager VIMSpc Payload Reports
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager VIMSpc Software
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Service Tool Software
988K, 990K, 992K and 994K Wheel Loaders Cat® Production Measurement Application / VIMSTM Network Manager Weigh Range Adjusting
416F2, 420F2 and 430F2 Backhoe Loaders Engine Air Filter Primary Element - Clean/Replace
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Air Cleaner Dust Valve - Clean/Inspect
990K Wheel Loader Systems Steering Control Group
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Engine Supplement Water Separator and Fuel Filter (Primary) - Remove and Install
Felling Head Limiter Crack Repair Procedure {6712} Felling Head Limiter Crack Repair Procedure {6712}
A New Felling Head Limiter Crack Repair Is Now Available for Certain Felling Heads {6712} A New Felling Head Limiter Crack Repair Is Now Available for Certain Felling Heads {6712}
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Engine Supplement Muffler - Remove and Install
New Gear Assemblies in the Transmission Pump Are Now Used on Certain 793F Off-Highway Trucks {3108, 5073} New Gear Assemblies in the Transmission Pump Are Now Used on Certain 793F Off-Highway Trucks {3108, 5073}
773E Off-Highway Truck Air System and Brakes Air Compressor and Governor - Test and Adjust
An Improved Inner Clutch Seal is Now Available For Certain 700 C-Series Articulated Trucks {3030, 3160} An Improved Inner Clutch Seal is Now Available For Certain 700 C-Series Articulated Trucks {3030, 3160}
2570D and 2670D Wheel Feller Buncher Engine Supplement Nitrogen Oxide Sensor - Remove and Install - Inlet
M325D MH Material Handler Axle Oil Sample - Obtain