CW16 Pneumatic Compactor Machine Electronic Control System Caterpillar


ECM - Replace

Usage:

CW-16 N6J
Prior to the replacement of the ECM, ensure that replacement is necessary. The ECM is seldom the cause of a failure. Always check that power is available to all the contacts of the ECM that are marked with "+ Battery".

Procedure

Note: Refer to Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program" before replacing the ECM.

  1. Turn the disconnect switch and the key start switch to the OFF position.

  2. Disconnect the machine harness connectors from the ECM.

  3. Verify that the part number of the replacement ECM is correct.

  4. Install the replacement ECM.

  5. Connect the machine harness to the ECM.

  6. Turn the disconnect switch and the key start switches to the ON position.

  7. Refer to Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program" to flash the software to the ECM.

Caterpillar Information System:

HFW232 Felling Saw Bearing for Grapple Arm - Lubricate
CW16 Pneumatic Compactor Machine Electronic Control System Connector Contact Description
CW16 Pneumatic Compactor Machine Electronic Control System ECM - Configure
CW16 Pneumatic Compactor Machine Electronic Control System ECM Software - Install
CW16 Pneumatic Compactor Machine Electronic Control System Wiring Harness (Short Circuit) - Test
CW16 Pneumatic Compactor Machine Electronic Control System Wiring Harness (Open Circuit) - Test
994K Large Wheel Loader Field Assembly Manual Lift Cylinder - Connect
AP355F Asphalt Paver Turbocharger - Inspect
CW16 Pneumatic Compactor Machine Electronic Control System Speed Sensor (Dual Signal) - Test
AP355F Asphalt Paver Fuel System Filter (In-Line) - Replace
AP355F Asphalt Paver Engine Oil Sample - Obtain
AP355F Asphalt Paver Engine Oil Level - Check
Cat® Detect Proximity Awareness for MineStar Onboard Version 4 GPS Accuracy - Check
Cat® Detect Proximity Awareness for MineStar Onboard Version 4 GPS Mast - Align
Procedure to Install a Bluetooth Module 481-7118 Wiring Kit on F2 Series Backhoe Loaders {1408} Procedure to Install a Bluetooth Module 481-7118 Wiring Kit on F2 Series Backhoe Loaders {1408}
CB64B, CB66B, and CB68B Asphalt Compactors Machine Systems Piston Pump (Vibratory) - Remove and Install
Cat® Detect Proximity Awareness for MineStar Onboard Version 4 GPS Orientation - Adjust
Communication Failure For Certain Versions Of Product Link PL641 and PL631 Modules {7606} Communication Failure For Certain Versions Of Product Link PL641 and PL631 Modules {7606}
A New Diesel Exhaust Fluid Filter is Now Available for C7.1 Machine Engines {108H} A New Diesel Exhaust Fluid Filter is Now Available for C7.1 Machine Engines {108H}
A New Crankshaft Is Available For Certain C4.4 Machine Engines {1202} A New Crankshaft Is Available For Certain C4.4 Machine Engines {1202}
Technical Analysis 1 (TA1) Visual Inspection for 795F AC Off-Highway Trucks {0372, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for 795F AC Off-Highway Trucks {0372, 1000, 7000, 753S, 7565}
A New Diesel Exhaust Fluid Filter is Now Available for C7.1 Engines {108H} A New Diesel Exhaust Fluid Filter is Now Available for C7.1 Engines {108H}
Technical Analysis 1 (TA1) Visual Inspection for Asphalt Pavers {0372, 1000, 7000, 753T, 7565} Technical Analysis 1 (TA1) Visual Inspection for Asphalt Pavers {0372, 1000, 7000, 753T, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Cold Planer {0372, 1000, 7000, 753T, 7565} Technical Analysis 1 (TA1) Visual Inspection for Cold Planer {0372, 1000, 7000, 753T, 7565}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.