CP54B, CS54B and CS64B Vibratory Soil Compactors Propel System Caterpillar

Axle - Rear (Without Brake)

Usage:

Show/hide table

Show/hide table

Table 1
Specification for 325-3644 Drive Axle Gp
Item	Qty	Part	Specification Description
1	2	212-5713 Plug As	Torque to 52 to 84 N·m (38 to 62 lb ft).
2	2	198-7811 Dowel	Before assembly, apply Loctite 638 to the mating surfaces.
3	2	207-4255 Plug	Before assembly, apply Loctite 638 to the threads.
4	1	197-9155 Breather	Torque to 5.0 to 10.5 N·m (44.3 to 92.9 lb in).
5	26	7X-2559 Bolt	Before assembly, apply red Loctite 270 to the threads.
5	26	7X-2559 Bolt	Torque to 266 to 294 N·m (196 to 217 lb ft).
6	-	-	After assembly, remove excess Loctite 518 from the interface of the housing assembly and the brake assembly.
7	6	226-4370 Self-Locking Bolt	Torque to 66.5 to 73.5 N·m (49 to 54.2 lb ft).
8	2	226-4366 Nut	Use any one of the following methods to tighten the nut:
			Torque to 950 to 1050 N·m (701 to 774 lb ft).
			Or
			Before assembly, apply 4C-5592 Anti-Seize Compound to the mating surfaces.
			Torque to 800 N·m (590 lb ft).
9	4	8C-7505 Flat Head Screw	Torque to 12.5 to 26.3 N·m (110.6 to 232.8 lb in).
10	5	152-6144 Drain Plug As	Torque to 39 to 63 N·m (29 to 46 lb ft).
11	2	210-3098 Seal	Before assembly, coat bores with 129-1938 Grease Cartridge.

Show/hide table

Show/hide table

Table 2
Specification for 226-4400 Axle Housing Gp
Item	Qty	Part	Specification Description
12	4	095-0674 Bolt	Torque to 51.4 to 83.0 N·m (37.9 to 61.2 lb ft).
13	12	199-0694 Bolt	Before assembly, apply Loctite 270 to the threads.
13	12	199-0694 Bolt	Torque to 171 to 189 N·m (126 to 139 lb ft).
14	2	198-7811 Dowel	Before assembly, apply Loctite 638 to the surface.
15	2	199-0695 Bolt	Torque to 6.5 to 13.7 N·m (57.5 to 121.3 lb in).
16	-	-	Before assembly, apply blue Loctite High Flex GM to both sides of the interface of the center assembly and the brake assembly. Remove excess Loctite after assembly.
17	1	226-4398 Bevel Gear Gp	Backlash is 0.18 to 0.20 mm (0.007 to 0.008 inch).
18	As required, use the following shims in order to adjust the pinion:
	1	199-0684 Shim	Thickness is 2.50 mm (0.098 inch).
	1	199-0685 Shim	Thickness is 2.60 mm (0.102 inch).
	1	199-0686 Shim	Thickness is 2.70 mm (0.106 inch).
	1	199-0687 Shim	Thickness is 2.80 mm (0.110 inch).
	1	199-0688 Shim	Thickness is 2.90 mm (0.114 inch).
	1	199-0689 Shim	Thickness is 3.00 mm (0.118 inch).
	1	199-0690 Shim	Thickness is 3.10 mm (0.122 inch).
	1	199-0691 Shim	Thickness is 3.20 mm (0.126 inch).
	1	199-0692 Shim	Thickness is 3.30 mm (0.130 inch).
	1	199-0693 Shim	Thickness is 3.40 mm (0.134 inch).
19	-	-	Stake the nut after the pinion bearing has been preloaded and the backlash has been set.