Braking System - Test
检查机器周边区域。 确保机器周围没有人员和障碍物。
在干燥、平整的表面上测试制动器。
测试制动器前系好座椅安全带。
下列测试用于确定行车制动器是否起作用。 这种测试不是为了测定制动器的最大制动力。 在一定的发动机转速下,维持机器所需要的制动器保持力,根据机器的不同而有差异。 这是由于发动机设置、传动系效率和制动保持能力的差异造成的。
- 起动发动机。 稍微升起铲斗。
- 接合行车制动器。 松开停车制动器
- 把变速箱操纵杆移到第三前进速档 。
- 逐渐增加发动机转速到高怠速。 机器不应移动。
Show/hide table
如果机器开始移动,发动机就要立即减速,并接合停车制动器。
- 降低发动机转速到低怠速。 将变速箱移至空档。 接合停车制动器。 将铲斗降至地面。 停止发动机。
Show/hide table
注意 |
---|
如果测试制动器的时候发现机器移动,请与当地的卡特彼勒代理商联系。 机器恢复工作之前,先让代理商检查,和对工作制动器做必要的修理。 |
检查机器周边区域。 确保机器周围没有人员和障碍物。
在干燥、平整的表面上测试制动器。
测试制动器前系好座椅安全带。
使用下列程序来确定停车制动器是否起作用。 这些测试不是用来测量制动器最大保持力的。 在一定的发动机转速下,维持机器所需要的制动器保持力,根据机器的不同而有差异。 这是由于发动机设置、传动系效率和制动保持能力的差异造成的。
- 起动发动机。 稍微升起铲斗。
- 接合停车制动器。
- 将变速箱控制杆移到第三前进速档,然后到空挡,然后回到第三前进速档。
注: 如果在辅助制动器仍旧接合时机器的行驶速度超过
6 km/h (3.7 mph) ,停车制动器指示灯应该亮起,并且停车制动器警报应该响起。 - 逐渐增加发动机转速到高怠速。 机器不应移动。
Show/hide table
如果机器开始移动,发动机要立即减速,并踩下行车制动器踏板。
- 降低发动机转速。 将变速箱移至空档。 将铲斗降至地面。 停止发动机。
Show/hide table
注意 |
---|
在测试制动器时,如果机器移动,请咨询卡特彼勒代理商。 必要时,请代理商来检查。在机器工作前,修复行车制动器。 |
Caterpillar Information System:
2009/04/20 A New Gas Spring Assembly is Available {4338}
587R Pipelayer Mirror - If Equipped
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Bank Valve (Backhoe) - Remove
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1403 - FMI 06
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1403 - FMI 05
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1403 - FMI 03
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1401 - FMI 03
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1402 - FMI 11
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1402 - FMI 06
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1402 - FMI 05
Installation Instructions for the 2Q-8548 Pilot Control Conversion Gp (Third Valve Kit) for the 938G Series II Wheel Loader and the 288-0733 Pilot Control Conversion Gp (Third Valve Kit) for the IT38G Series II Integrated Toolcarrier{5057, 5059 Installation Instructions for the 2Q-8548 Pilot Control Conversion Gp (Third Valve Kit) for the 938G Series II Wheel Loader and the 288-0733 Pilot Control Conversion Gp (Third Valve Kit) for the IT38G Series II Integrated Toolcarrier{5057, 5059
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1402 - FMI 03
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Programming Parameters
416E Backhoe Loader Parking Brake - Check/Adjust
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines ECM Will Not Accept Factory Passwords
2009/02/16 A New Lamp Group (Beacon) is Now Used {1429, 1431}
AccuGrade® (CD610) Sensor - Adjust - Mainfall Sensor
AccuGrade® (CD610) Sensor - Adjust - Blade Slope Sensor
AccuGrade® (CD610) Sensor - Adjust - Rotation Sensor
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1403 - FMI 11
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1404 - FMI 03
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1404 - FMI 05
AccuGrade® GPS v11 for CD700 General Information
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1404 - FMI 06