Water Pump - Remove
Removal Procedure
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
- Drain the coolant into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Remove bolts (1) and belt guard (2) .
Show/hide table
 | |
| Illustration 1 | g01156851 |
- Remove belt (3) .
Show/hide table
 | |
| Illustration 2 | g01156853 |
- Remove hose (4) and tube (5) .
Show/hide table
 | |
| Illustration 3 | g01160563 |
- Remove bolts (7) and guard assembly (6) .
Show/hide table
 | |
| Illustration 4 | g01160572 |
- Disconnect tube assembly (8) and hose (9). Remove bolts (10) and housing (11). Remove tube (12) .
Show/hide table
 | |
| Illustration 5 | g01160585 |
- Remove bolt (14) and pulley (13) .
Show/hide table
 | |
| Illustration 6 | g01160593 |
- Remove bolts (17). Loosen clamps (15). Remove adapter (16) .
Show/hide table
 | |
| Illustration 7 | g01160596 |
- Disconnect hose (20). Remove bolts (19). Remove elbow (18) .
Show/hide table
 | |
| Illustration 8 | g01160601 |
- Remove bolts (22) and water pump (21) .
Show/hide table
 | |
| Illustration 9 | g01160642 |
Caterpillar Information System:
2005/09/26 New Fuel Transfer Pump {1256}
3500 Engines Low Engine Oil Pressure
C11 and C15 Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
120M and 12M Motor Graders Hydraulic and Steering System Accumulator (Blade Cushion)
2005/04/18 Replace the Gear when the Sleeve Bearing is Replaced {1212, 1234}
2005/04/18 Replace the Gear when the Sleeve Bearing is Replaced {1212}
2005/04/25 Correction to Specifications , "Brake Control Valve (Service)" {4265}
ECM Replacement Procedure on 700 Series Articulated Trucks{7610} ECM Replacement Procedure on 700 Series Articulated Trucks{7610}
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Braking System Pressure Switch (Parking Brake Oil)
Filtration Procedure for E Series Vibratory Compactors {0680, 0768, 5050, 5056} Filtration Procedure for E Series Vibratory Compactors {0680, 0768, 5050, 5056}
793D Off-Highway Truck Differential and Final Drive Oil Sample - Obtain
Instructions for Converting Hot Saw to Intermittent Saw {5051, 5051, 5057, 6543} Instructions for Converting Hot Saw to Intermittent Saw {5051, 5051, 5057, 6543}
789C Off-Highway Truck Drive Shaft Slip Joint - Lubricate
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
784C and 785C Off-Highway Truck/Tractors Jacking Locations
725, 730 and 730 Ejector Articulated Trucks Engine Supplement Water Pump - Install
PM-201 Cold Planer Machine Lowering with Engine Stopped
725, 730 and 730 Ejector Articulated Trucks Engine Supplement In-Line Refrigerant Dryer - Remove and Install
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Glossary of Electrical Terms
12M, 140M and 160M Motor Graders Hydraulic and Steering System Control Valve (Wing Tilt)
2005/05/23 New ROPS Films, FOPS Films and TOPS Films Have Been Designed {7557}
C11 and C15 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
C4.4 Industrial Engine Starting the Engine
12M, 140M and 160M Motor Graders Hydraulic and Steering System Control Valve (Ripper)