Accumulator (Blade Cushion)
Show/hide table
 | |
| Illustration 1 | g03609057 |
Show/hide table
| Specification for 219-7265 Blade Cushion Accumulator Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | - | - | Torque to 217 ± 10 N·m (160 ± 7 lb ft). |
| 2 | - | - | Torque to 217 ± 10 N·m (160 ± 7 lb ft). |
| - | For more information on the 219-7265 Blade Cushion Accumulator Gp , refer to theTesting and Adjusting, "Accumulator (Blade Cushion) - Test and Charge" in the "Testing and Adjusting" manual for your machine. | ||
Caterpillar Information System:
2005/04/18 Replace the Gear when the Sleeve Bearing is Replaced {1212, 1234}
2005/04/18 Replace the Gear when the Sleeve Bearing is Replaced {1212}
2005/04/25 Correction to Specifications , "Brake Control Valve (Service)" {4265}
ECM Replacement Procedure on 700 Series Articulated Trucks{7610} ECM Replacement Procedure on 700 Series Articulated Trucks{7610}
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Braking System Pressure Switch (Parking Brake Oil)
Filtration Procedure for E Series Vibratory Compactors {0680, 0768, 5050, 5056} Filtration Procedure for E Series Vibratory Compactors {0680, 0768, 5050, 5056}
793D Off-Highway Truck Differential and Final Drive Oil Sample - Obtain
Instructions for Converting Hot Saw to Intermittent Saw {5051, 5051, 5057, 6543} Instructions for Converting Hot Saw to Intermittent Saw {5051, 5051, 5057, 6543}
Instructions for Converting Hot Saw to Harvester Head Saw{5051, 5051, 5057, 6543} Instructions for Converting Hot Saw to Harvester Head Saw{5051, 5051, 5057, 6543}
784C and 785C Off-Highway Truck/Tractors Differential and Final Drive Oil Level - Check
2005/04/18 An Improved Crankshaft is Used {1202}
2005/04/25 Improved Engine Software and Improved Monitor Software Now used {7490}
C11 and C15 Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
3500 Engines Low Engine Oil Pressure
2005/09/26 New Fuel Transfer Pump {1256}
725, 730 and 730 Ejector Articulated Trucks Engine Supplement Water Pump - Remove
789C Off-Highway Truck Drive Shaft Slip Joint - Lubricate
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
784C and 785C Off-Highway Truck/Tractors Jacking Locations
725, 730 and 730 Ejector Articulated Trucks Engine Supplement Water Pump - Install
PM-201 Cold Planer Machine Lowering with Engine Stopped
725, 730 and 730 Ejector Articulated Trucks Engine Supplement In-Line Refrigerant Dryer - Remove and Install
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Glossary of Electrical Terms
12M, 140M and 160M Motor Graders Hydraulic and Steering System Control Valve (Wing Tilt)